Joystick Controls
Show/hide table
Illustration 1 | g00559405 |
The machine control pattern can be varied by changing the hydraulic hose connections. See your Caterpillar dealer for the procedure.
The machine control pattern is initially set at the factory to the SAE system, as shown. The pattern on the left pertains to the left joystick and the pattern on the right pertains to the right joystick.
Show/hide table
Stick Out (1) - Move the joystick to this position in order to move the stick outward. |
Show/hide table
Swing Right (2) - Move the joystick to this position in order to swing the upper structure to the right. |
Show/hide table
Stick In (3) - Move the joystick to this position in order to move the stick inward. |
Show/hide table
Swing Left (4) - Move the joystick to this position in order to swing the upper structure to the left. |
Show/hide table
Boom Lower (5) - Move the joystick to this position in order to lower the boom. |
Show/hide table
Bucket Dump (6) - Move the joystick to this position in order to dump the bucket. |
Show/hide table
Boom Raise (7) - Move the joystick to this position in order to raise the boom. |
Show/hide table
Bucket Close (8) - Move the joystick to this position in order to close the bucket. |
HOLD (9) - When you release the joystick from any position, the joysticks will return to the HOLD position. Movement of the upper structure will stop.
Two functions may be performed at the same time by moving a joystick diagonally.
Caterpillar Information System:
2000/08/07 The Main Control Valve is Improved for Use with the "Bent Axis Travel Motor" {5051}
2013/10/14 New Expander Rings and Backup Rings are Available {0617}
2014/08/11 Diagnostic Cables and Harnesses Are Available {0785}
M325B Material Handler Machine Systems Check Valve (Stabilizer) - Assemble
M325B Material Handler Machine Systems Check Valve (Stabilizer) - Disassemble
330C Excavator Joystick Controls
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) System Schematic
3126B Engines General Information
MP-15, MP-20, MP-30 and MP-40 Multi Processors Multi-Processor Housing
3176C and 3196 Engines for Caterpillar Built Machines Poor Acceleration or Response
MP-15, MP-20, MP-30 and MP-40 Multi Processors Multi-Processor Housing
MP-15, MP-20, MP-30 and MP-40 Multi Processors Multi-Processor Housing
307C Excavator Window Wiper and Washer Control
322C Excavator Machine Systems Stick Bearings and Seals - Remove
320C Excavator Equipment Lowering with Engine Stopped
320C Forest Machine Machine Systems Boom Cylinder - Assemble
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) TPS Maximum Payload Speed Manager
C-9 Engines for Caterpillar Built Machines Flywheel Housing
307C Excavator Hydraulic System Gear Pump (Pilot) - Test
C-9 Engines for Caterpillar Built Machines Compression Brake
320C U Excavator Leaving the Machine
330C Excavator Securing the Machine
365B, 365B Series II and 365BL Excavators Window Wiper and Washer Control
G112, G115, G125 and G140 Mechanical Grapple Stick Bracket - Remove and Install