Multi-Processor Housing
Show/hide table
 | |
| Illustration 1 | g00729803 |
(1) Apply Loctite 270 to the 36 bolts that secure the gear and bearing to the hydraulic rotator.
Torque on the 36 bolts ... 530 ± 70 N·m (391 ± 52 lb ft)
(2) Apply Loctite 270 to the 36 bolts that secure the gear and bearing to the lower housing.
Torque on the 36 bolts ... 530 ± 70 N·m (391 ± 52 lb ft)
Show/hide table
 | |
| Illustration 2 | g00707623 |
Diameters of pin (3)
-
(7) Diameter ... 141.944 ± .012 mm (5.5883 ± 0.0005 inch) (8) Diameter ... 139.944 ± .012 mm (5.5096 ± 0.0005 inch) (9) Diameter ... 137.4 mm (5.41 inch) (10) Diameter ... 136.944 ± .012 mm (5.3915 ± 0.0005 inch) (11) Diameter ... 134.944 ± .012 mm (5.3127 ± 0.0005 inch)
(4) Bore in the bushing ... 195.20 ± .05 mm (7.6850 ± 0.0020 inch)
(5) Diameter of the bushing ... 194.860 ± .02 mm (7.6716 ± 0.0008 inch)
Bore in the bushing ... 169.860 ± .02 mm (6.6874 ± 0.0008 inch)
(6) Diameter of the pin ... 139.944 ± .012 mm (5.5096 ± 0.0005 inch)
Caterpillar Information System:
3176C and 3196 Engines for Caterpillar Built Machines Poor Acceleration or Response
MP-15, MP-20, MP-30 and MP-40 Multi Processors Multi-Processor Housing
MP-15, MP-20, MP-30 and MP-40 Multi Processors Multi-Processor Housing
JF Series Starting Motor Pinion Continues to Engage after Engine Starts
MP-15, MP-20, MP-30 and MP-40 Multi Processors Shear Jaw
G112, G115, G125 and G140 Mechanical Grapple Mounting Bracket
G112, G115, G125 and G140 Mechanical Grapple Mounting Bracket
3126B Engines Electronic Control System Components
3176C and 3196 Engines for Caterpillar Built Machines Intermittent Low Power or Power Cutout
G112, G115, G125 and G140 Mechanical Grapple Mounting Bracket
MP-15, MP-20, MP-30 and MP-40 Multi Processors Hydraulic Rotator Cycle Time - Check
320C Excavator Fine Swing Control - If Equipped
3126B Engines General Information
5130, 5130B and 5230 Excavators, 784B, 785B, 785C, 789B, 789C, 793B and 793C Off-Highway Truck/Tractors and 992G, 994 and 994D Wheel Loaders Vital Information Management System (VIMS) System Schematic
330C Excavator Joystick Controls
M325B Material Handler Machine Systems Check Valve (Stabilizer) - Disassemble
M325B Material Handler Machine Systems Check Valve (Stabilizer) - Assemble
2014/08/11 Diagnostic Cables and Harnesses Are Available {0785}
2013/10/14 New Expander Rings and Backup Rings are Available {0617}
2000/08/07 The Main Control Valve is Improved for Use with the "Bent Axis Travel Motor" {5051}
330C Excavator Joystick Controls
307C Excavator Window Wiper and Washer Control
322C Excavator Machine Systems Stick Bearings and Seals - Remove
320C Excavator Equipment Lowering with Engine Stopped