Vibration Damper and Pulley - Remove and Install
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | - | Guide Bolts (5/8-18 NF) | 2 |
- Remove cover (1) from the front of the engine.
- Remove the V-belt.
Show/hide table
Illustration 2 g01095215 - Remove two bolts that are opposite each other. Install Tooling (A). Remove the remainder of bolts (2).
- Use a suitable lifting device to remove crankshaft vibration damper and pulley (3) from the crankshaft. The weight of the crankshaft vibration damper and pulley is approximately
45 kg (100 lb) .
Show/hide table
Illustration 1 | g01095210 |
Show/hide table
Required Tools | |||
---|---|---|---|
Tool | Part Number | Part Description | Qty |
A | - | Guide Bolts (5/8-18 NF) | 2 |
- If the pulley was removed from the crankshaft vibration damper, the studs must be installed to a torque of
65 ± 10 N·m (48 ± 7 lb ft) and the nuts tightened to a torque of135 ± 20 N·m (100 ± 15 lb ft) .Show/hide tableIllustration 3 g01095215 - Install Tooling (A) in the end of the crankshaft.
- Use a suitable lifting device to install the crankshaft vibration damper and pulley (3) on Tooling (A). The weight of the crankshaft vibration damper and pulley is approximately
45 kg (100 lb) . - Install bolts (2). Remove Tooling (A) and install remaining bolts (2).
- Install the V-belt on the pulley.
Show/hide table
Illustration 4 g01095210 - Install cover (1) on the front of the engine.
Caterpillar Information System:
Alignment of Two-Bearing Generators{4471} Alignment of Two-Bearing Generators{4471}
3600 Distillate Fuel Engines Engine Power Ratings
Generator Set Control Panel for Switchgear Conversion CID 0100 FMI 08 Pressure Sensor (Engine Oil) Abnormal Signal - Test
G3408 and G3412 Engines Cooling System
G3606 and G3608 Engines Flywheel and Coupling Guards - Remove and Install
3412E, C30 and C32 Marine Engines Flywheel - Install
G3408 and G3412 Engines Lubrication System
G3408 and G3412 Engines Governor Adjustment Procedure
G3606 and G3608 Engines Housing (Rear) - Install
G3606 and G3608 Engines Housing (Rear) - Remove
G3408 and G3412 Engines Air Inlet And Exhaust System
G3606 and G3608 Engines Manual Barring Group - Assemble
G3606 and G3608 Engines Crankcase Breather - Remove and Install
G3408 and G3412 Engines Basic Block
G3408 and G3412 Engines Air Starting System
G3606 and G3608 Engines Valve Cover - Remove and Install
G3408 and G3412 Engines Electrical System
3412E, C30 and C32 Marine Engines Front Cover - Remove
3412E, C30 and C32 Marine Engines Front Cover - Install
Generator Set Control Panel for Switchgear Conversion CID 0102 FMI 08 Pressure Sensor (Boost) Abnormal Signal - Test
G3606 and G3608 Engines Rocker Arm - Remove
G3606 and G3608 Engines Rocker Arm - Install
Generator Set Control Panel for Switchgear Conversion CID 0110 FMI 08 Temperature Sensor (Engine Coolant) Abnormal Signal - Test
Generator Set Control Panel for Switchgear Conversion CID 0172 FMI 04 Temperature Sender (Inlet Air) Voltage Below Normal - Test