Housing (Rear) - Remove
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-7409     | 吊环螺栓     | 1     |
开始:
- 拆下涡轮增压器。 请参阅拆解和组装, "涡轮增压器 - 拆卸"。
- 卸下磁电机。 请参阅拆解和装配磁电机, "- 拆卸"。
- 拆下曲轴后密封。 请参阅拆解和组装, "曲轴后密封 - 拆卸"。
- 拆下起动马达。 请参阅拆解和装配电动起动马达, "- 拆卸"。
- 拆下手动盘机总成。 请参阅拆解和组装, "手动盘机总成 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 断开机油泵上的机油泵进油管。
- 拧松将油底壳固定到位的所有螺栓,直至油底壳和前壳体、缸体和后壳体之间的间隙为 3.17 mm (0.125 inch)。
- 卸下将油底壳固定至后壳体的螺栓。
- 将工具 (A) 安装在后壳体的顶部。 将适当的起吊设备连接到工具 (A) 上。
注: 卸下后壳体之前,确保已从其内部和外部卸下所有螺栓。
Show/hide table
图 1 | g00562674 |
- 卸下将后壳体固定至缸体的螺栓。 小心将后壳体从缸体上移开。 后壳体的重量约为 210 kg (463 lb)。
- 将密封垫和 O 形密封圈从缸体上拆下。
Caterpillar Information System:
G3408 and G3412 Engines Air Inlet And Exhaust System
G3606 and G3608 Engines Manual Barring Group - Assemble
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Control Panel (Engine)
G3606 and G3608 Engines Manual Barring Group - Disassemble
3600 Heavy Fuel Engines Gauges and Indicators
G3408 and G3412 Engines Fuel System
3412E, C30 and C32 Marine Engines Flywheel - Remove
G3408 and G3412 Engines Ignition System
3600 Heavy Fuel Engines Model View Illustrations
G3408 and G3412 Engines Air Starting System
G3408 and G3412 Engines Electrical System
G3606 and G3608 Engines Manual Barring Group - Install
G3606 and G3608 Engines Housing (Rear) - Install
G3408 and G3412 Engines Governor Adjustment Procedure
G3408 and G3412 Engines Lubrication System
3412E, C30 and C32 Marine Engines Flywheel - Install
G3606 and G3608 Engines Flywheel and Coupling Guards - Remove and Install
G3408 and G3412 Engines Cooling System
Generator Set Control Panel for Switchgear Conversion CID 0100 FMI 08 Pressure Sensor (Engine Oil) Abnormal Signal - Test
3600 Distillate Fuel Engines Engine Power Ratings
Alignment of Two-Bearing Generators{4471} Alignment of Two-Bearing Generators{4471}
3412E, C30 and C32 Marine Engines Vibration Damper and Pulley - Remove and Install
G3606 and G3608 Engines Crankcase Breather - Remove and Install
G3408 and G3412 Engines Basic Block