Housing (Rear) - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件说明     | 数量     |
A     | 1P-7409     | 吊环螺栓     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 将垫片和 O 形密封圈放置在缸体后部的合适位置上。
Show/hide table
图 1 | g00562674 |
- 将工具 (A) 安装在后壳体的顶部。 使用适当的提升装置。 后壳体的重量约为 210 kg (463 lb)。
- 将后壳体放置在缸体的合适位置上。 安装将后壳体固定到位的螺栓。
- 调整后壳体与缸体之间的垫片,使其与后壳体底部齐平。
- 安装将油底壳固定至后壳体的螺栓。
- 均匀地拧紧固定油底壳的所有螺栓,将油底壳升到合适位置。
- 将机油泵进油管连接至机油泵。
End By:
- 安装手动盘机组件。 请参阅 拆解和组装, "手动盘机组件 - 安装"。
- 安装起动马达。 请参阅 拆解和装配, "电动起动马达 - 安装"。
- 安装曲轴后密封。 请参阅 拆解和组装, "曲轴后油封 - 安装"。
- 安装磁电机。 请参阅 拆解和装配磁电机, "- 安装"。
- 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
G3606 and G3608 Engines Housing (Rear) - Remove
G3408 and G3412 Engines Air Inlet And Exhaust System
G3606 and G3608 Engines Manual Barring Group - Assemble
G3408C, G3412C, G3508, G3512 and G3516 Gas Engine Driven Chillers Control Panel (Engine)
G3606 and G3608 Engines Manual Barring Group - Disassemble
3600 Heavy Fuel Engines Gauges and Indicators
G3408 and G3412 Engines Fuel System
3412E, C30 and C32 Marine Engines Flywheel - Remove
G3408 and G3412 Engines Ignition System
3600 Heavy Fuel Engines Model View Illustrations
G3408 and G3412 Engines Air Starting System
G3408 and G3412 Engines Electrical System
G3408 and G3412 Engines Governor Adjustment Procedure
G3408 and G3412 Engines Lubrication System
3412E, C30 and C32 Marine Engines Flywheel - Install
G3606 and G3608 Engines Flywheel and Coupling Guards - Remove and Install
G3408 and G3412 Engines Cooling System
Generator Set Control Panel for Switchgear Conversion CID 0100 FMI 08 Pressure Sensor (Engine Oil) Abnormal Signal - Test
3600 Distillate Fuel Engines Engine Power Ratings
Alignment of Two-Bearing Generators{4471} Alignment of Two-Bearing Generators{4471}
3412E, C30 and C32 Marine Engines Vibration Damper and Pulley - Remove and Install
G3606 and G3608 Engines Crankcase Breather - Remove and Install
G3408 and G3412 Engines Basic Block
G3408 and G3412 Engines Air Starting System