Rocker Arm - Install
安装步骤
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 检查摇臂中的轴承是否磨损。
注: 维修时更换的新摇臂组件需要加工。 有关具体说明,请咨询当地 Caterpillar 经销商。
- 检查轴是否磨损。
- 确保摇臂和摇臂轴内的润滑油道通畅。
- 将新的 O 形密封圈安装在摇臂上。 在 O 形密封圈上涂抹清洁的发动机机油。
- 将按钮 (1) 安装在摇臂上。
Show/hide table
图 1 | g00563304 |
- 将清洁的发动机机油涂在摇臂轴 (5) 和摇臂轴承上。
Show/hide table
图 2 | g00563302 |
- 将摇臂 (8) 、摇臂 (7) 和摇臂 (6) 安装在摇臂轴上的原始位置。
- 将盘 (2) 放在摇臂轴末端上的合适位置。 安装将盘 (2) 固定到位的螺栓 (3) 。
- 将螺栓 (4) 安装在摇臂轴内。
End By: 安装气门机构。 请参阅 拆解和组装, "气门机构 - 安装"。
Caterpillar Information System:
G3606 and G3608 Engines Rocker Arm - Remove
Generator Set Control Panel for Switchgear Conversion CID 0102 FMI 08 Pressure Sensor (Boost) Abnormal Signal - Test
3412E, C30 and C32 Marine Engines Front Cover - Install
3412E, C30 and C32 Marine Engines Front Cover - Remove
G3408 and G3412 Engines Electrical System
G3606 and G3608 Engines Valve Cover - Remove and Install
G3408 and G3412 Engines Air Starting System
G3408 and G3412 Engines Basic Block
G3606 and G3608 Engines Crankcase Breather - Remove and Install
3412E, C30 and C32 Marine Engines Vibration Damper and Pulley - Remove and Install
Alignment of Two-Bearing Generators{4471} Alignment of Two-Bearing Generators{4471}
3600 Distillate Fuel Engines Engine Power Ratings
Generator Set Control Panel for Switchgear Conversion CID 0110 FMI 08 Temperature Sensor (Engine Coolant) Abnormal Signal - Test
Generator Set Control Panel for Switchgear Conversion CID 0172 FMI 04 Temperature Sender (Inlet Air) Voltage Below Normal - Test
Electric Protection System Energize-To-Shutoff (ETS) For Generator Set, Industrial and Marine Diesel Engines Troubleshooting the ETS Partial Protection System (OP, WT) - 3200-3400 Engines
G3606 and G3608 Engines Valve Mechanism - Remove
Generator Set Control Panel for Switchgear Conversion CID 0175 FMI 08 Temperature Sensor (Engine Oil) Abnormal Signal - Test
Generator Set Control Panel for Switchgear Conversion CID 0248 FMI 02 CAT Data Link Incorrect - Test
Generator Set Control Panel for Switchgear Conversion CID 0460 FMI 08 Pressure Sensor (Fuel) Abnormal Signal - Test
Generator Set Control Panel for Switchgear Conversion CID 0819 FMI 02 Display Data Link Incorrect - Test
797 Off-Highway Truck Power Train Relief Valve (Torque Converter Inlet)
Generator Set Control Panel for Switchgear Conversion CID 0821 FMI 03 Display Power Supply Voltage Above Normal - Test
G3606 and G3608 Engines Valve Mechanism - Install
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines General Troubleshooting Information