PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING THE LEVELING SWITCH AND/OR REPLACING, IF NECESSARY, THE LEVELING VALVE GROUP ON CERTAIN 323DL EXCAVATORS Caterpillar


PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING THE LEVELING SWITCH AND/OR REPLACING, IF NECESSARY, THE LEVELING VALVE GROUP ON CERTAIN 323DL EXCAVATORS

Usage:

REBE4596-00

27Feb2009


U-87
A-77

 
Priority
  
 Parts stock action needed 

PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING THE LEVELING SWITCH AND/OR REPLACING, IF NECESSARY, THE LEVELING VALVE GROUP ON CERTAIN 323DL EXCAVATORS

5479 1408 7301
PI31640
NOTE:

This Program must be administered as soon as possible. When reporting the repair, use "PI31640" as the Part Number and "7751" as the Group Number, "56" as the Warranty Claim Description Code and "T" as the SIMS Description code. Exception: If the repair is done after failure, use "PI31640" as the Part Number, "7751" as the Group Number, "96" as the Warranty Claim Description Code, and "Z" as the SIMS Description Code.

NOTE:

When submitting claim for Parts Stock Action, Use the appropriate 99Z as the s/n, the appropriate Service Letter Program Number as the Part number in the Part Causing Failure field, "7751" as the Group Number, "56" as the Description Code.

NOTE:

The information supplied in this service letter may not be valid after the termination date of this program. Do not perform the work outlined in this Service Letter after the termination date without first contacting your Caterpillar product analyst.


COMPLETION DATE

TERMINATION DATE

31Aug2009 28Feb2010

PROBLEM

The 2677639/">267-7639 Switch Assembly needs to be installed and the 2650067/">265-0067 Valve Group needs to be replaced, if necessary, on certain 323DL Excavators. If the 2677639/">267-7639 Switch Assembly is not installed and the correct 2650067/">265-0067 Valve Group is not being used, the leveling function may not be properly performed.

AFFECTED PRODUCT

Model Identification Number
*******Group  1*******
323D L  LFL00103-00156, 158-159
*******Group  2*******
323D L  LFL00160, 163, 167-168, 170, 172-177
*******Group  3*******
323D L  LFL00195-00198

PARTS NEEDED

Qty

Part Number Description
*******Group 1*******
1 2650067 VALVE GP-SOL -A
1 2677639 SWITCH AS-ROCKER
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 40% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.
*******Group 2*******
1 2677639 SWITCH AS-ROCKER
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 40% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.
*******Group 3*******
1 2650067 VALVE GP-SOL -A
In order to allow equitable parts availability to all participating dealers, please limit your initial parts order to not exceed 40% of dealership population. This is an initial order recommendation only, and the ultimate responsibility for ordering the total number of parts needed to satisfy the program lies with the dealer.

ACTION REQUIRED

****Parts Stock ****

Inspect all 2650067/">265-0067 Valve Group-Solenoids that are in dealer parts stock. If a blue W letter is marked at the function plate, remove the valve group from parts stock and do not use. If a red V is marked at the function plate, the valve should be placed back into stock and can be used. Refer to Image 1.

 
Image1
 
****Affected Product****
Refer to the attached Rework Procedure as follows:

Group 1 - Perform the Complete Rework Procedure
Group 2 - Perform the 2677639/">267-7639 Switch Assembly Installation only
Group 3 - Perform the Inspection and Replacement of the 2650067/">265-0067 Valve Group -
Solenoid only

OWNER NOTIFICATION

U.S. and Canadian owners will receive the attached Owner Notification.

SERVICE CLAIM ALLOWANCES

****Parts Stock****

Submit one claim for all parts removed from dealer parts stock.

 
 
****Affected Product****
Caterpillar
Dealer Suggested
Customer Suggested
Parts %
Labor Hrs%
Parts %
Labor Hrs%
Parts %
Labor Hrs%
*******Group 1*******
100%
100%
0%
0%
0%
0%
 NOTE: This is a 2.0-hour job for Group 1

Caterpillar
Dealer Suggested
Customer Suggested
Parts %
Labor Hrs%
Parts %
Labor Hrs%
Parts %
Labor Hrs%
*******Group 2*******
100%
100%
0%
0%
0%
0%
 NOTE: This is a 0.5-hour job for Group 2

Caterpillar
Dealer Suggested
Customer Suggested
Parts %
Labor Hrs%
Parts %
Labor Hrs%
Parts %
Labor Hrs%
*******Group 3*******
100%
100%
0%
0%
0%
0%

 NOTE: This is a 1.5-hour job for Group 3


PARTS DISPOSITION

****Parts Stock****
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

****Affected Product****
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.

 
COPY OF OWNER NOTIFICATION FOR U.S. AND CANADIAN OWNERS

XYZ Corporation
3240 Arrow Drive
Anywhere, YZ 99999

PRIORITY - PRODUCT IMPROVEMENT PROGRAM FOR INSTALLING THE LEVELING SWITCH AND/OR REPLACING, IF NECESSARY, THE LEVELING VALVE GROUP

MODELS INVOLVED - 323DL EXCAVATORS

Dear Caterpillar Product Owner:


The 2677639/">267-7639 Switch Assembly needs to be installed and the 2650067/">265-0067 Valve Group needs to be replaced, if necessary, on the products listed below. If the 2677639/">267-7639 Switch Assembly is not installed and the correct 2650067/">265-0067 Valve Group is not being used, the leveling function may not be properly performed. You will not be charged for the service performed.

Contact your local Caterpillar dealer immediately to schedule this service. The dealer will advise you of the time required to complete this service.

Please refer the dealer to their Service Letter dated 27Feb2009 when scheduling this service.

We regret the inconvenience this may cause you, but urge you to have this service performed as soon as possible to prevent unscheduled downtime.



Caterpillar Inc.

Identification #(s)



Attached to 27Feb2009 Service Letter


Rework Procedure


 
1. The 2677639/">267-7639 Switch Assembly installation.

1.1 - Remove Right Side Control Panel Cover (1) as shown in Image 1.1.1
Image1.1.1
 
1.2 - Connect the 2677639/">267-7639 Switch Assembly to the connector that has the gray wire L978 (refer to Electrical Schematic, KENR8266, if necessary). Attach Switch (2) to Cover (1) and reassemble to the right side control panel. Refer to Image 1.2.1.
Image1.2.1
 
2. Inspection and replacement of the 2650067/">265-0067 Valve Group-Solenoid

Refer to Disassembly and Assembly Manual, RENR7500, for general recommendations and system pressure release.

2.1 - Remove Bottom Panel (3) to access the valve group. Refer to Image 1.3.1.
Image1.3.1
 
2.2 - Inspect the function plate letter color at the installed solenoid valve, as shown in Image 1.4.1.
- If a red V letter is marked, the correct 2650067/">265-0067 Valve Group-Solenoid is being used and no action is required.
- If a blue W letter is marked, replace the 2650067/">265-0067 Valve Group-Solenoid with a new one.
Image1.4.1
 
2.3 - To replace the 2650067/">265-0067 Valve Group-Solenoid, loosen and remove Bolts (4). Remove the Valve Group-Solenoid (5) and install the new one. Apply a light coating of clean hydraulic oil to the o-rings before installation. After installed, tighten the bolts to a torque of 6.9 +/- 0.7 Nm.
Image1.5.1
 
2.4 - Install Bottom Panel (3).
 
 

Caterpillar Information System:

PRODUCT SUPPORT PROGRAM FOR MODIFYING CERTAIN PIN GRABBER PERFORMANCE BUCKETS FOR USE WITH CERTAIN DB, B, AND 315 LINKAGE PIN GRABBER COUPLERS PRODUCT SUPPORT PROGRAM FOR MODIFYING CERTAIN PIN GRABBER PERFORMANCE BUCKETS FOR USE WITH CERTAIN DB, B, AND 315 LINKAGE PIN GRABBER COUPLERS
PRODUCT IMPROVEMENT PROGRAM FOR REMOVING 7Y-4945 AND 087-5550 BACK-UP RINGS FROM DEALER PARTS STOCK PRODUCT IMPROVEMENT PROGRAM FOR REMOVING 7Y-4945 AND 087-5550 BACK-UP RINGS FROM DEALER PARTS STOCK
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING, AND REWORKING IF NEEDED, THE MAIN HYDRAULIC PUMP REGULATOR ON CERTAIN 385C, 385CL, 385CL MH AND 385C FS EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING, AND REWORKING IF NEEDED, THE MAIN HYDRAULIC PUMP REGULATOR ON CERTAIN 385C, 385CL, 385CL MH AND 385C FS EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE HYDRAULIC SWING MOTOR ON CERTAIN 330C, 330C L, 330D, AND 330D L EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REWORKING THE HYDRAULIC SWING MOTOR ON CERTAIN 330C, 330C L, 330D, AND 330D L EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE MAIN PUMP ON CERTAIN 320D, 320DL, 324D, 324DL, 325D EXCAVATORS AND 950H, 962H, 966H, 972H WHEEL LOADERS PRODUCT SUPPORT PROGRAM FOR REPLACING THE MAIN PUMP ON CERTAIN 320D, 320DL, 324D, 324DL, 325D EXCAVATORS AND 950H, 962H, 966H, 972H WHEEL LOADERS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE FAN DRIVE PULLEY AND THE CRANKSHAFT PULLEY ON CERTAIN 308D MINI HYDRAULIC EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPLACING THE FAN DRIVE PULLEY AND THE CRANKSHAFT PULLEY ON CERTAIN 308D MINI HYDRAULIC EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING LOWER COMPACTOR ASSEMBLY ON CERTAIN CVP40 VIBRATORY PLATE COMPACTORS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING LOWER COMPACTOR ASSEMBLY ON CERTAIN CVP40 VIBRATORY PLATE COMPACTORS
PRODUCT SUPPORT PROGRAM FOR REWORKING THE HYDRAULIC SWING MOTOR ON CERTAIN 330C L, 330D L, AND 336D L EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REWORKING THE HYDRAULIC SWING MOTOR ON CERTAIN 330C L, 330D L, AND 336D L EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR FLASHING NEW SOFTWARE AND REPLACING FUEL FILTERS ON CERTAIN 320D EXCAVATORS EQUIPPED WITH C6.4 ENGINES PRODUCT IMPROVEMENT PROGRAM FOR FLASHING NEW SOFTWARE AND REPLACING FUEL FILTERS ON CERTAIN 320D EXCAVATORS EQUIPPED WITH C6.4 ENGINES
PRODUCT SUPPORT PROGRAM FOR REPLACING THE 231-8048 OIL COOLER HOSE ON CERTAIN 3056E, DV-924G, 924G, 928G, AND 930G SMALL WHEEL LOADERS; AP-600 PAVERS; CP-563E, CP-573E, CP-663E, CS-563E, CS-573E, CS-583E, CS-663E, AND CS-683E VIBRATORY COMPACTORS; DV PRODUCT SUPPORT PROGRAM FOR REPLACING THE 231-8048 OIL COOLER HOSE ON CERTAIN 3056E, DV-924G, 924G, 928G, AND 930G SMALL WHEEL LOADERS; AP-600 PAVERS; CP-563E, CP-573E, CP-663E, CS-563E, CS-573E, CS-583E, CS-663E, AND CS-683E VIBRATORY COMPACTORS; DV
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE SWIVEL GROUP STOP AND FOR CHECKING THE ENGINE OIL FILTER HOSES ON CERTAIN 307C MINI HYDRAULIC EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE SWIVEL GROUP STOP AND FOR CHECKING THE ENGINE OIL FILTER HOSES ON CERTAIN 307C MINI HYDRAULIC EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR INSTALLING THE INCREASED STICK SPEED KIT ON CERTAIN M313C AND M313D WHEELED EXCAVATORS PRODUCT SUPPORT PROGRAM FOR INSTALLING THE INCREASED STICK SPEED KIT ON CERTAIN M313C AND M313D WHEELED EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPAIRING WELD CRACKS ON B, CB, DB, AND TB BUCKETS FOR CERTAIN 320D, 323D, 324D, 325D, AND 330D EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPAIRING WELD CRACKS ON B, CB, DB, AND TB BUCKETS FOR CERTAIN 320D, 323D, 324D, 325D, AND 330D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM TO CEASE OPERATION, INSPECT, AND REPLACE IF NEEDED, THE BOOM CYLINDERS ON CERTAIN 330D EXCAVATORS PRODUCT IMPROVEMENT PROGRAM TO CEASE OPERATION, INSPECT, AND REPLACE IF NEEDED, THE BOOM CYLINDERS ON CERTAIN 330D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR RE-TIGHTENING THE 292-7595 OR 292-7590 TUBE ASSEMBLY ON CERTAIN 319D L AND 319D LN EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR RE-TIGHTENING THE 292-7595 OR 292-7590 TUBE ASSEMBLY ON CERTAIN 319D L AND 319D LN EXCAVATORS
PRODUCT SUPPORT PROGRAM FOR REPLACING THE PIN ASSEMBLIES ON CERTAIN 330D AND 336D EXCAVATORS PRODUCT SUPPORT PROGRAM FOR REPLACING THE PIN ASSEMBLIES ON CERTAIN 330D AND 336D EXCAVATORS
PRODUCT SUPPORT PROGRAM TO REPLACE THE 194-0820 BLOCK ON CERTAIN 330D L, 336D L, AND 330D MH FCR EXCAVATORS PRODUCT SUPPORT PROGRAM TO REPLACE THE 194-0820 BLOCK ON CERTAIN 330D L, 336D L, AND 330D MH FCR EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE CYLINDER HEAD LIFTING EYE BOLT HOLE ON VARIOUS 3508, 3512, AND 3516 ENGINES PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE CYLINDER HEAD LIFTING EYE BOLT HOLE ON VARIOUS 3508, 3512, AND 3516 ENGINES
PRODUCT SUPPORT PROGRAM FOR INSTALLING THE CAB AIR DUCT ASSEMBLIES ON CERTAIN 321D AND 328D EXCAVATORS PRODUCT SUPPORT PROGRAM FOR INSTALLING THE CAB AIR DUCT ASSEMBLIES ON CERTAIN 321D AND 328D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE HYDRAULIC CYLINDER RODS ON CERTAIN 319D EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE HYDRAULIC CYLINDER RODS ON CERTAIN 319D EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE MAIN CONTROL VALVE ON CERTAIN 345C, 345CL, 345D AND 345DL EXCAVATORS PRODUCT IMPROVEMENT PROGRAM FOR INSPECTING THE MAIN CONTROL VALVE ON CERTAIN 345C, 345CL, 345D AND 345DL EXCAVATORS
PRODUCT SUPPORT PROGRAM TO INSPECT AND REPLACE THE FUEL HOSE CONDUIT ON CERTAIN 345D L EXCAVATORS PRODUCT SUPPORT PROGRAM TO INSPECT AND REPLACE THE FUEL HOSE CONDUIT ON CERTAIN 345D L EXCAVATORS
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING HANDLES AND WALKWAY ON CERTAIN 385C AND 385CL EXCAVATORS THAT ARE EQUIPPED WITH A CAB RISER (900 MM) PRODUCT IMPROVEMENT PROGRAM FOR REPLACING HANDLES AND WALKWAY ON CERTAIN 385C AND 385CL EXCAVATORS THAT ARE EQUIPPED WITH A CAB RISER (900 MM)
PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 109-4440 PLUG ON ALL MP20 AND VT40 MULTIPROCESSORS PRODUCT IMPROVEMENT PROGRAM FOR REPLACING THE 109-4440 PLUG ON ALL MP20 AND VT40 MULTIPROCESSORS
Back to top
The names Caterpillar, John Deere, JD, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
CH-Part.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only.