Pistons and Connecting Rods - Install
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 5P-3525     | 活塞环压缩器     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 转动曲轴,直至轴承接缝位于下止点。 轴承轴颈位于下止点以便安装活塞。
- 将清洁的发动机机油涂覆在曲轴轴颈和缸套的内侧。 在活塞环和连杆轴承上抹上清洁的发动机机油。
- 移动活塞上的活塞环,直至环开口间隔大约 120 度。
- 将活塞放入缸套,活塞上的 "V" 标记与缸体上的 "V" 标记对准。 将工具 (A) 在缸体上放置到位,然后压缩活塞环。
Show/hide table
图 1 | g00483337 |
- 将活塞推入到缸套中,并推出活塞环压缩器。
Show/hide table
注意 |
---|
活塞和缸体上必须可以看见 "V" 标记。 如果 "V" 标记不可见,安装活塞时气门开口必须朝向缸体中的推杆开口。 如果活塞未正确安装,可能导致损坏。 |
- 将连杆 (1) 导入到曲轴上的适当位置。
Show/hide table
图 2 | g00483701 |
- 将清洁的发动机机油 (SAE 30) 涂覆到连杆轴承的下轴瓦和连杆螺栓上。
- 安装连杆盖 (2) 和固定连杆盖的螺母。 将两个螺母拧紧至 40 ± 4 N·m (30 ± 3 lb ft)。 标记出螺母的位置。 将每个螺母再拧紧 90 度(1/4 圈)。
Show/hide table
注意 |
---|
在已安装了连杆盖后,确保对准识别标记。 |
- 对于其余的活塞和连杆,重复第 1 至 8 步。
End By:
- 安装发动机机油泵。 请参考 解体与组装, "发动机机油泵 - 安装"。
- 安装发动机油底壳护板。 请参考 解体与组装, "发动机油底壳护板 - 拆卸和安装"。
- 安装间隔板。 请参考 解体与组装, "间隔板 - 拆卸和安装"。
Caterpillar Information System:
3412E and C30 Engines Cylinder Head
3406E Truck Engines Accessory Drive
3306C Engines for Caterpillar Built Machines Piston Cooling Jet
G3606 and G3608 Engines Governor Type
3406E Truck Engine Belt Tensioner
3612 and 3616 Fast Vessel Engines Engine Oil Sample - Obtain
3406E On-Highway Engine Engine Oil Filter Base - Install
3304B and 3306B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Remove
3306B Industrial Engine Fuel System - Prime
3304B and 3306B Engines for Caterpillar Built Machines Flywheel - Install
3306B Industrial Engine Air Starting
3306B Industrial Engine Flywheel - Remove
3406C (PEEC III) Truck Engine Flywheel
3306C Engines for Caterpillar Built Machines Connecting Rod Bearing Journal
3306C Engines for Caterpillar Built Machines Main Bearing Journal
3406E Truck Engines Air Inlet Elbow
Gas Engine Driven Chiller Driveline Product Information
3306C Engines for Caterpillar Built Machines Cylinder Liner Projection
3304B and 3306B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
3304B and 3306B Engines for Caterpillar Built Machines Pistons and Connecting Rods - Assemble
3412E and C30 Engines Turbocharger
784C and 785C Off-Highway Truck/Tractors Air System and Brakes Solenoid Valve (Air Horn)
3406E and 3456 Engines for Caterpillar Built Machines Exhaust Manifold - Remove and Install
3406E On-Highway Engine Turbocharger - Install