Clean Emissions Module - Remove and Install - Top Mounted Diesel Oxidation Catalyst (DOC)
开始:
- 拆下 DOC 和 SCR 之间的柔性排气管。 有关正确步骤,请参阅拆解和装配, "柔性排气管 - 拆卸和安装(DOC 和 SCR 之间的柔性排气管)"。
- 从涡轮增压器和柴油氧化催化器 (DOC) 上拆下柔性排气管。 有关正确步骤,请参阅拆解和装配, "柔性排气管 - 拆卸和安装(来自涡轮增压器和柴油氧化催化器 (DOC) 的柔性排气管)"。
- 拆下柴油机排气处理液 (DEF) 喷射器。 有关正确的步骤,请参阅拆解和组装, " DEF 喷油器和安装件 - 拆卸和安装"。
- 将适当的起吊设备连接到柴油氧化催化器 (DOC) (1) 上。
- 将螺栓 (4) 和 (5) 从 DOC (1) 上拆下。 拆卸螺栓过程中,支承 DOC。
- 使用适当的起吊设备将 DOC (1) 从支架 (6) 上拆下。
- 如有必要,将拼合衬套 (3) 从支架 (6) 上拆下。
- 必要时,拆下支架 (6)。 有关正确的步骤,请参阅拆解和装配, "支架和安装件 (CEM) - 拆卸和安装(顶装式 DOC)"。
Show/hide table
图 1 | g03798704 |
- 确保 DOC 和支架没有磨损或损坏。 更换所有磨损或损坏的部件。
Show/hide table
图 2 g03798704 - 如有必要,安装支架 (6)。 有关正确的步骤,请参阅拆解和装配, "支架和安装件 (CEM) - 拆卸和安装(顶装式 DOC)"。
- 如有必要,将拼合衬套 (3) 安装到支架 (6) 上。 安装拼合衬套,以便可以安装 DOC (1)。
- 将适当的起吊设备连接到 DOC (1) 上。
- 使用适当的起吊设备将 DOC (1) 定位到支架 (6) 上。
- 将螺栓 (4) 和 (5) 安装到 DOC (1) 上。 用手上紧螺栓。 安装螺栓过程中,支承 DOC。
- 拧紧螺栓 (4) 和 (5) 至扭矩为
25 N·m (221 lb in) 。 - 如果已安装新的 DOC,转至电子维修工具,并选择"维修"菜单,然后"氧化催化器更换复位"。
结束:
- 安装 DOC 和 SCR 之间的柔性排气管。 有关正确步骤,请参阅拆解和装配, "柔性排气管 - 拆卸和安装(DOC 和 SCR 之间的柔性排气管)"。
- 安装来自涡轮增压器和柴油氧化催化器 (DOC) 的柔性排气管。 有关正确步骤,请参阅拆解和装配, "柔性排气管 - 拆卸和安装(来自涡轮增压器和柴油氧化催化器 (DOC) 的柔性排气管)"。
- 安装柴油机排气处理液 (DEF) 喷射器。 有关正确的步骤,请参阅拆解和组装, " DEF 喷油器和安装件 - 拆卸和安装"。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Clean Emissions Module - Remove and Install - Flywheel Mounted Diesel Oxidation Catalyst (DOC)
C3.4B Engines for Caterpillar Built Machines Selective Catalytic Reduction (SCR) Canister - Remove and Install
C3.4B Engines for Caterpillar Built Machines Flexible Exhaust Pipe - Remove and Install - Flexible Exhaust Pipe Between DOC and the SCR
C2.2 Engines for Caterpillar Built Machines Flywheel Housing - Remove and Install
C2.2 Engines for Caterpillar Built Machines Crankshaft Rear Seal - Remove and Install
C4.4 Engines Exhaust Temperature Is High
C7.1 Engines Solenoid Valve - Test - Solenoid Valves that Connect to the Dosing Control Unit (DCU)
C9.3 Marine Engines Exhaust Manifold
C9.3 Marine Engines Cylinder Head Valves
3516C Marine Engines Accessory Drive (Front) - Remove and Install
794 AC Off-Highway Truck Power Train Sensor - Remove and Install - Contactor Current
390F MHPU Mobile Hydraulic Power Unit Machine Systems Pump Control (Negative Flow) - Test
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C4.4 Engines Soot Sensor - Test
390F MHPU Mobile Hydraulic Power Unit Machine Systems Power Shift Pressure - Calibrate
3516C Marine Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
794 AC Off-Highway Truck Power Train Sensor - Remove and Install - Chopper Current
794 AC Off-Highway Truck Power Train Sensor - Remove and Install - Phase Current
3516C Marine Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
Adaptive Control System (ACS) Advanced Calibration Procedures {5051, 5063} Adaptive Control System (ACS) Advanced Calibration Procedures {5051, 5063}
794 AC Off-Highway Truck Power Train Power Generator - Remove and Install
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Temperature Sensor Exhaust before SCR
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Temperature Sensor Exhaust After SCR