Temperature Sensor (Exhaust) - Remove and Install
- 如有必要,拆下柴油微粒滤清器安装支架。 有关正确的步骤,请参阅拆解和装配, "支架和安装件 (CEM) - 拆卸和安装"。
Show/hide table
图 1 g03817970 为清晰起见,已拆下 EGR 热屏蔽 - 将线束组件 (2) 从排气温度传感器接头 (1) 上断开。
- 将排气温度传感器接头 (1) 滑出支架 (3)。
- 将排气温度传感器 (5) 从排气歧管 (4) 上拆下。
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | Bostik 纯镍 防粘结剂 |
1 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
Show/hide table
图 2 g03817970 为清晰起见,已拆下 EGR 热屏蔽 - 将工具 (A) 涂覆到排气温度传感器 (5) 的螺纹上。
- 将排气温度传感器 (5) 安装到排气歧管 (4) 上。 将排气温度传感器拧紧至扭矩为
45 N·m (33 lb ft) 注: 确保排气温度传感器的线束布设正确。
- 将排气温度传感器接头 (1) 滑入支架 (3)。
- 将线束组件 (2)(未显示)连接到排气温度传感器接头 (1) 上。
- 如有必要,安装柴油微粒滤清器安装支架。 有关正确的步骤,请参阅拆解和装配, "支架和安装件 (CEM) - 拆卸和安装"。
Caterpillar Information System:
794 AC Off-Highway Truck Power Train Power Generator - Remove and Install
Adaptive Control System (ACS) Advanced Calibration Procedures {5051, 5063} Adaptive Control System (ACS) Advanced Calibration Procedures {5051, 5063}
3516C Marine Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
794 AC Off-Highway Truck Power Train Sensor - Remove and Install - Phase Current
794 AC Off-Highway Truck Power Train Sensor - Remove and Install - Chopper Current
3516C Marine Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
390F MHPU Mobile Hydraulic Power Unit Machine Systems Power Shift Pressure - Calibrate
C4.4 Engines Soot Sensor - Test
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C3.4B Engines for Caterpillar Built Machines Clean Emissions Module - Remove and Install - Top Mounted Diesel Oxidation Catalyst (DOC)
C3.4B Engines for Caterpillar Built Machines Clean Emissions Module - Remove and Install - Flywheel Mounted Diesel Oxidation Catalyst (DOC)
C3.4B Engines for Caterpillar Built Machines Selective Catalytic Reduction (SCR) Canister - Remove and Install
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Temperature Sensor Exhaust before SCR
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Temperature Sensor Exhaust After SCR
C2.2 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C7.1 Engines Speed Control (Analog) - Test
C18 Marine Auxiliary Engine Maintenance Interval Schedule - Prime Power
G3612 and G3616 Engines Engine Support - Remove and Install
C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C18 Marine Generator Set Maintenance Interval Schedule - Prime Power
C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
G3612 and G3616 Engines Electronic Control Module - Remove and Install
C18 Marine Generator Set Maintenance Interval Schedule - Prime Power
3500 Generator Sets with Dynamic Gas Blending Product Description