Temperature Sensor (Exhaust) - Remove and Install - Temperature Sensor Exhaust before SCR
开始:
- 将蓄电池断路开关转到断开位置。
- 断开温度传感器 (1) 的线束组件。
- 将温度传感器从选择性催化还原 (SCR) 组件 (2) 上拆下。
Show/hide table
图 1 | g03823064 |
Show/hide table
所需工具 | |||
工具 | 零件号 | 零件描述 | 数量 |
A | - | Bostik 纯镍 防粘结剂 |
1 |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 确保所有部件清洁、无磨损或损坏。 如有必要,更换所有磨损或损坏的部件。
- 将工具 (A) 涂抹到温度传感器 (1) 的螺纹上。
- 将温度传感器安装到选择性催化还原 (SCR) 组件 (2) 上。 将温度传感器拧紧至扭矩为
45 N·m (33 lb ft) 。
Show/hide table
图 2 | g03823064 |
结束:
- 将蓄电池断路开关转到接通位置。
Caterpillar Information System:
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install
794 AC Off-Highway Truck Power Train Power Generator - Remove and Install
Adaptive Control System (ACS) Advanced Calibration Procedures {5051, 5063} Adaptive Control System (ACS) Advanced Calibration Procedures {5051, 5063}
3516C Marine Engines Crankshaft Rear Seal and Wear Sleeve - Remove and Install
794 AC Off-Highway Truck Power Train Sensor - Remove and Install - Phase Current
794 AC Off-Highway Truck Power Train Sensor - Remove and Install - Chopper Current
3516C Marine Engines Crankshaft Front Seal and Wear Sleeve - Remove and Install
390F MHPU Mobile Hydraulic Power Unit Machine Systems Power Shift Pressure - Calibrate
C4.4 Engines Soot Sensor - Test
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
C3.4B Engines for Caterpillar Built Machines Clean Emissions Module - Remove and Install - Top Mounted Diesel Oxidation Catalyst (DOC)
C3.4B Engines for Caterpillar Built Machines Clean Emissions Module - Remove and Install - Flywheel Mounted Diesel Oxidation Catalyst (DOC)
C3.4B Engines for Caterpillar Built Machines Temperature Sensor (Exhaust) - Remove and Install - Temperature Sensor Exhaust After SCR
C2.2 Engines for Caterpillar Built Machines Crankshaft Pulley - Remove and Install
C7.1 Engines Speed Control (Analog) - Test
C18 Marine Auxiliary Engine Maintenance Interval Schedule - Prime Power
G3612 and G3616 Engines Engine Support - Remove and Install
C2.2 Engines for Caterpillar Built Machines Crankshaft Front Seal - Remove and Install
C18 Marine Generator Set Maintenance Interval Schedule - Prime Power
C2.2 Engines for Caterpillar Built Machines Housing (Front) - Remove
G3612 and G3616 Engines Electronic Control Module - Remove and Install
C18 Marine Generator Set Maintenance Interval Schedule - Prime Power
3500 Generator Sets with Dynamic Gas Blending Product Description
C18 Marine Engine Maintenance Interval Schedule - Prime Power