Tracks - Inspect
Show/hide table
Fingers can be burned from hot pins and bushings. The pins and bushings in a dry joint can become very hot. It is possible to burn the fingers if there is more than brief contact with these components. |
Show/hide table
注意事項 |
---|
撞擊履帶插銷的末端會使履帶接頭出現明顯的軸向間隙,並可能導致過早出現故障。 |
使用建議方式,以延長底盤系統的壽命。 使用建議方式,以避免停機時間過長。
- 操作機器期間,請聆聽是否有不尋常的尖銳刺耳聲。 這些噪音可能代表接頭過乾。
- 檢查所有履帶組件是否有過度磨損的情形。
- 操作機器之後,立即檢查是否有接合處過乾問題。 操作機器之後,輕觸每個履帶銷或襯套。 在所有發熱的過乾履帶插銷接頭上作標記。
- 請勿使用大錘敲擊履帶插銷末端來鬆開履帶接頭。
Show/hide table
插圖 1 | g03708823 |
如果發現接頭過乾或滲漏情形,請洽詢 Cat 代理商的自訂履帶服務專家。 Cat 代理商的自訂履帶服務專家可執行履帶檢查作業。
Caterpillar Information System:
3516B Generator Set Engines with Dynamic Gas Blending Inlet Air Is Restricted
C175-16 Locomotive Engine Speed/Timing - Test
3512C Engine Air Inlet Manifold - Remove and Install
3516C Marine Engines Exhaust Elbow
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Speed Control - Test
PM820, PM822, and PM825 Cold Planer Track Shoe Bolts - Tighten
460-8972 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 460-8972 Major Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
3516C Marine Engines Turbocharger Oil Lines
3516C Marine Engines Fuel Injector
462-1133 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000} 462-1133 Top End Overhaul Foundational Kit for 3412 Generator Set Engines{1000}
C27 and C32 Generator Set Engines Fan Drive
3306B-XQ200 Rental Generator Set Engine Refill Capacities
3500E EPA Tier 4 Final and IMO-II/III Switchable Marine Engines Transmission Oil Temperature Is High
PM820, PM822, and PM825 Cold Planer Upper Conveyor Deflectors (Second Stage) - Inspect/Replace
PM820, PM822, and PM825 Cold Planer Upper Conveyor Support Cables - Check
PM820, PM822, and PM825 Cold Planer Water Spray Nozzles - Clean
G3304B and G3306B Engines Air/Fuel Ratio Problem
PM820, PM822, and PM825 Cold Planer Water Spray System - Inspect
DE Series Generator Set With Cat C4.4 Engine Model View Illustrations
2014/12/12 A New Ignition Transformer Group Is Available For Certain G3500C, G3500E, and G3600 Engines {1409, 1550}
PM820, PM822, and PM825 Cold Planer Water Tank Strainer - Clean and Inspect
Procedure to Bypass EGR Relay in EMCP2 Controls For Generator Sets{1908, 4490, 4493} Procedure to Bypass EGR Relay in EMCP2 Controls For Generator Sets{1908, 4490, 4493}
2014/09/26 New Fuel Priming Pump and Secondary Fuel Filter Base for Certain C7.1,C6.6 and C4.4 Engines {1256, 1258, 1261, 1263, 1274}
C4.4 Industrial Engine Soot Antenna