Electrohydraulic System Oil Pressure Is Low
使用本步骤对电子液压系统低油压进行故障诊断与排除。 此外,如果以下任一事件代码为激活或记录状态,应使用本步骤。
Show/hide table
J1939 代码和描述 | 注释 |
---|---|
1762-1
液压压力:低 - 最高严重程度(3) |
电子液压执行器系统的压力传感器检测到压力低于 发动机将停机。 |
- 代码
- 安全阀
- 机油压力
Show/hide table
故障诊断与排除测试步骤 | 数值 | 结果 |
---|---|---|
1. 检查代码 A. 连接 Cat® 电子技师 (ET) 与维修工具接头。 B。 查找与事件代码系统相关的现行代码。 |
代码 |
结果:相关代码为现行状态。 修理:在继续进行此测试前,诊断并排除所有相关代码。 结果:代码激活或被记录。 转至测试步骤 2。 |
2. 检查安全阀设置 |
安全阀 |
结果:安全阀设置正常。 转至测试步骤 3。 结果:安全阀设置不正常。 修理:调节安全阀。 有关更多信息,请参阅测试和调整, "发动机调速 - 调整"。 如果故障未得到排除,则转至测试步骤 3。 |
3. 检查压力安全阀 如果卸压阀脏污,阀可能卡住。 如果卸压阀卡在打开的位置,液压油压力将太低。 A. 检查后冷器上的安全阀。 B。 检查液压泵上的安全阀是否泄漏并/或调整。 |
安全阀 |
结果:安全阀正常。 继续测试步骤 4。 结果:安全阀不正常。 修理:清洁或更换安全阀。 调节安全阀,请参考测试和调整, "发动机调速 - 调整",了解更多信息。 如果故障未得到排除,则转至测试步骤 4。 |
4. 检查液压油压力是否过低 A. 检查液压油油位。 B。 当发动机盘车时,使用仪表检查电子液压系统液压泵进出口的液压油压力。 C. 将该压力与测试和调整, "发动机调速 - 调整"中的压力相比较。 D. 如有可能,在发动机处于正常工作温度时,使用仪表在液压泵出口处检查电子液压系统液压的油压。 E. 将该压力与测试和调整, "发动机调速 - 调整"中的压力相比较。 |
机油压力 |
结果:油压不正常。 修理:检查电子液压系统是否泄漏。 检查液压泵。 根据需要进行修理。 确认修理后故障得到排除。 |
如果以上步骤未解决问题,请联系当地 Cat 代理商的技术通信员(TC)。 如需进一步的帮助,您的 TC 可以通过代理商解决方案网络(DSN)与您交谈。
Caterpillar Information System:
G3600 A4 Engines Inlet Air Is Restricted
G3600 A4 Engines Intake Manifold Air Temperature Is High
G3600 A4 Engines Engine Overspeeds
G3600 A4 Engines Air Starting Motor Problem
C11 and C13 Engines Engine Oil Pan
C13, C15, and C18 Tier 4 Final Engines Engine Oil Pan
C13, C15, and C18 Tier 4 Final Engines Piston and Rings
C13, C15, and C18 Tier 4 Final Engines Inlet Manifold Air Pressure Sensor
C13, C15, and C18 Tier 4 Final Engines Relay (ARD Nozzle Heater)
C13, C15, and C18 Tier 4 Final Engines Flywheel Housing Cover
C11 and C13 Engines Turbocharger
C13, C15, and C18 Tier 4 Final Engines Air Lines
C11 and C13 Engines Exhaust Manifold
C11 and C13 Engines Engine Oil Filter Base
C11 and C13 Engines Exhaust Manifold
C11 and C13 Engines Camshaft
C11 and C13 Engines Engine Oil Cooler
C280-08 Marine Engine Electrical System
G3600 A4 Engines Fuel Energy Content Problem
G3600 A4 Engines Fuel Pressure Problem
C280-08 Marine Engine Sensors and Electrical Components
C280-08 Marine Engine Emergency Stopping
2013/12/10 New Software Is Used On Certain SCR Retrofit Aftertreatment Systems {1901, 1902, 1920}
C175 Cylinder Head Lifting Device{0374, 0599, 0632, 0703, 1100} C175 Cylinder Head Lifting Device{0374, 0599, 0632, 0703, 1100}