Modulating Valve (Transmission Clutch) - Remove and Install
拆卸步骤
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
Show/hide table
| 注意 |
|---|
在检验、保养、测试、调整及维修发动机时，请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前，要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品，请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
- 卸下螺栓 (1) 和防护罩 (2) 。
Show/hide table
 | |
| 图 1 | g01859357 |
- 断开线束组件 (3) 。
Show/hide table
 | |
| 图 2 | g01859376 |
- 拆下螺栓 (4) 和调节阀 (5) 。
- 拆下 O 形密封圈 (6) 。 拆下螺母 (7) 和垫圈。 拆下线圈组件 (8) 。
Show/hide table
 | |
| 图 3 | g01859381 |
- 对其余调节阀重复步骤3到1。
安装步骤
Show/hide table
| 注意 |
|---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
注: 检查 O 形密封圈、密封件和垫片。 更换磨损或损坏的 O 形密封圈、密封件和垫片。
注: 利用所密封的润滑剂润滑 O 形密封圈。
- 安装线圈组件 (8) 。 安装螺母 (7) 和垫圈。 将螺母 (7) 上紧到 13 ± 1.5 N·m (115 ± 13 lb in) 的扭矩。 安装 O 形密封圈 (6) 。
Show/hide table
| | |
| 图 4 | g01859381 |
- 安装调节阀 (5) 。 安装螺栓 (4) 。 用 30 ± 4 N·m (22 ± 3 lb ft) 的扭矩拧紧螺栓 (4) 。 连接线束组件 (3) 。
Show/hide table
| | |
| 图 5 | g01859376 |
- 安装防护罩 (2) 和螺栓 (1) 。 用 28 ± 7 N·m (21 ± 5 lb ft) 的扭矩拧紧螺栓 (1) 。
Show/hide table
| | |
| 图 6 | g01859357 |
Caterpillar Information System:
CX35-P800 Petroleum Transmission and Petroleum Power Train Packages Modulating Valve (Transmission Clutch) - Remove and Install
C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Assemble
C6.6 Industrial Engine Camshaft Bearings
C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Disassemble
C7.1 Engines for Caterpillar Built Machines Vibration Damper and Pulley
C7.1 Industrial Engine and Generator Set System Overview
C7.1 Industrial Engine and Generator Set Glossary
3500 Industrial Engines Exhaust Flange
C13 Engines for Caterpillar Built Machines Engine Oil Filter Base - Remove and Install
C13 Engine for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
C175-16 Locomotive Engine Engine Misfires, Runs Rough or Is Unstable
G3500 Generator Sets Crankshaft Vibration Damper - Inspect - 1500 RPM G3520 engines (if equipped with an oil fed damper)
C6.6 Industrial Engine Boost Pressure Sensor
C13 Engine for Caterpillar Built Machines Fuel Pressure Regulator - Remove and Install
C9.3 Engines for Caterpillar Built Machines Oil Pressure Is Low
C9.3 Tier 4 Interim Engines Oil Contains Fuel
C13 Engine for Caterpillar Built Machines Electronic Unit Injector Sleeve - Remove and Install
C6.6 Industrial Engine Front Housing and Covers
C7.1 Industrial Engine Turbocharger - Series Turbochargers
C6.6 Industrial Engine Electronic Control Module
C13 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Remove
C6.6 Industrial Engine Crankcase Breather
C6.6 Industrial Engine Valve Mechanism Cover
C13 Engines for Caterpillar Built Machines Rocker Arm and Shaft - Install