Crankshaft - Remove
Start By:
- Remove pistons and connecting rods.
Show/hide table
| NOTICE |
|---|
|
If the crankshaft has been reground or replaced, the height of the piston above the cylinder block must be inspected. It is necessary to remove the cylinder head to inspect the height of the piston above the cylinder block. |
Note: Before you disassemble, measure the side clearance of the crankshaft. Measure it when you reassemble.
- Remove bolts (1).
Show/hide table
Illustration 2 g06016439 - Rotate crankshaft (2) and align the crankshaft journals with the reliefs (X) in the Cylinder Block. Use two people to pull the crankshaft out of the cylinder block. The weight of crankshaft (2) is approximately
24 kg (53 lb) .Show/hide table
Illustration 3 g06016479 - Remove bolts (3) and main bearing case assemblies (4).
Show/hide table
Illustration 4 g06016876 - Remove main bearings (6) and thrust bearings (5).
Show/hide table
Illustration 5 g06016885 - Remove crankshaft bearing (7).
Show/hide table
| |
| Illustration 1 | g06016404 |
Caterpillar Information System:
Improved Positive Pin Retention (PPR) & Positive Pin Retention 2 (PPR2) Tooling {0700, 6108, 6501, 6502, 6513} Improved Positive Pin Retention (PPR) & Positive Pin Retention 2 (PPR2) Tooling {0700, 6108, 6501, 6502, 6513}
320GC, 320 and 323 Excavators Machine Systems Duo-Cone Conventional Seals - Install
Improved Brackets Are Used on Tilt Cylinder Guard for Certain K-Series and M-Series Medium Wheel Loaders {5104, 7150, 7164} Improved Brackets Are Used on Tilt Cylinder Guard for Certain K-Series and M-Series Medium Wheel Loaders {5104, 7150, 7164}
910K, 914K and 920K Compact Wheel Loaders Bucket Tips - Inspect/Replace
990K Wheel Loader and 844K Wheel Dozer Machine Systems Brake Accumulator - Remove and Install
910K, 914K and 920K Compact Wheel Loaders Operation Information
D8T Track-Type Tractor Engine Air Filter Primary and/or Secondary Element - Clean/Replace
C1.7 and C2.2 Industrial Engines Self-Diagnostics
Exhaust Gas Valve (NRS) for C7.1, and C6.6 Engines {5137} Exhaust Gas Valve (NRS) for C7.1, and C6.6 Engines {5137}
990K Wheel Loader and 844K Wheel Dozer Engine Supplement Fuel Manifold (ARD) - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Automatic Lubrication - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Engine Supplement Muffler and Mounting - Remove and Install
D9R Cab Installation {1408, 7177, 7301, 7325} D9R Cab Installation {1408, 7177, 7301, 7325}
D11T Multishank and Single Shank Ripper Installation {6310} D11T Multishank and Single Shank Ripper Installation {6310}
963K Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Brake Control Valve (Parking) - Remove and Install
844K Wheel Dozer and 990K Wheel Loader Power Train Crankcase Guard - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Brake Control Valve (Service) - Remove and Install
844K Wheel Dozer and 990K Wheel Loader Power Train Bottom Guards (Front) - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Bucket - Remove and Install
844K Wheel Dozer and 990K Wheel Loader Power Train Axle Oil Cooler - Remove and Install
A Special Instruction Must be Followed when Installing Retaining-Rings on ELRT Control Valves {3030, 3083, 3157} A Special Instruction Must be Followed when Installing Retaining-Rings on ELRT Control Valves {3030, 3083, 3157}
A New Water Valve Is Used with the Cabs Air Conditioner on Certain Medium Wheel Loaders, Large Wheel Loaders Wheel Dozers, Soil Compactors, and Landfill Compactors {7320} A New Water Valve Is Used with the Cabs Air Conditioner on Certain Medium Wheel Loaders, Large Wheel Loaders Wheel Dozers, Soil Compactors, and Landfill Compactors {7320}
An Improved Backup Alarm is Used on Certain K-Series Small Wheel Loaders and B3 Series SSL/MTL/CTLs {1408, 7051} An Improved Backup Alarm is Used on Certain K-Series Small Wheel Loaders and B3 Series SSL/MTL/CTLs {1408, 7051}