Bucket - Remove and Install
Show/hide table
| Required Tools | |||
| Tool | Part Number | Part Description | Qty |
| A | 1U-9200 | Lever Puller Hoist Gp | 1 |
| B | 9U-6800 | Nut | 1 |
| 237-9180 | Receiving Sleeve As | 1 | |
| 4C-6504 | Puller Rod | 1 | |
| 346-5029 | Hydraulic Cylinder | 1 | |
| 350-7768 | Electric Hydraulic Pump Gp(1) | 1 | |
| C | 9U-6810 | Nut | 1 |
| 9U-6815 | Puller Stud | 1 | |
| 316-1491 | Hydraulic Cylinder | 1 | |
| 350-7768 | Electric Hydraulic Pump Gp(1) | 1 | |
| D | - | Loctite 263 | - |
| E | - | Moly Grease | - |
Show/hide table
| (1) | If electrical power is not available, use 9U-6600 Hand Hydraulic Pump. |
Start By:
a. Connect the steering frame lock.
- Attach a suitable lifting device and Tooling (A) to lever assembly (1). Attach the hook of Tooling (A) to link assembly (2) with a suitable lifting device. The weight of link assembly (2) is approximately
313 kg (690 lb) . - Remove bolts (3) and plate (4).
Show/hide table
Illustration 3 g06016174 Show/hide table
Illustration 4 g06016175 - Install Tooling (B) to pin assembly (5). Attach a suitable lifting device to Tooling (B). The weight of pin assembly (5) and Tooling (B) is approximately
175 kg (386 lb) . Remove pin assembly (5). Inspect lip seals (6) and replace if necessary.Show/hide table
Illustration 5 g06016197 Show/hide table
Illustration 6 g06016200 - Remove bolts (7) and plate (8).
Note: Mark the shims and the location of the shims for assembly.
- Install Tooling (C) to pin assembly (9). Attach a suitable lifting device to Tooling (C). The weight of pin assembly (9) and Tooling (C) is approximately
154 kg (340 lb) . Remove pin assembly (9).Show/hide table
Illustration 7 g06016222 - Lower link assembly (2) to clear the work tool (10) at removal. When the pin assemblies are removed, separate the steering frame lock. Start the engine and move the machine away from the work tool (10).
- Turn the engine start switch to the OFF position. Raise link assembly (2). Use a cable and cable clamps to tie the link assembly to the lever and bearing assembly.
Show/hide table
| |
| Illustration 1 | g06016168 |
Show/hide table
| |
| Illustration 2 | g06016165 |
- Install the work tool in the reverse order of removal.
- Check and replace lip seals (6) if necessary. Apply Tooling (D) to bore prior to install lip seals (6).
- Apply Tooling (E) to pin assemblies (5) and (9).
Caterpillar Information System:
844K Wheel Dozer and 990K Wheel Loader Power Train Bottom Guards (Front) - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Brake Control Valve (Service) - Remove and Install
844K Wheel Dozer and 990K Wheel Loader Power Train Crankcase Guard - Remove and Install
990K Wheel Loader and 844K Wheel Dozer Machine Systems Brake Control Valve (Parking) - Remove and Install
963K Track-Type Loader Machine Systems Fan and Gear Motor (Hydraulic Fan) - Remove and Install
D11T Multishank and Single Shank Ripper Installation {6310} D11T Multishank and Single Shank Ripper Installation {6310}
D9R Cab Installation {1408, 7177, 7301, 7325} D9R Cab Installation {1408, 7177, 7301, 7325}
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Crankshaft - Remove
Improved Positive Pin Retention (PPR) & Positive Pin Retention 2 (PPR2) Tooling {0700, 6108, 6501, 6502, 6513} Improved Positive Pin Retention (PPR) & Positive Pin Retention 2 (PPR2) Tooling {0700, 6108, 6501, 6502, 6513}
320GC, 320 and 323 Excavators Machine Systems Duo-Cone Conventional Seals - Install
Improved Brackets Are Used on Tilt Cylinder Guard for Certain K-Series and M-Series Medium Wheel Loaders {5104, 7150, 7164} Improved Brackets Are Used on Tilt Cylinder Guard for Certain K-Series and M-Series Medium Wheel Loaders {5104, 7150, 7164}
910K, 914K and 920K Compact Wheel Loaders Bucket Tips - Inspect/Replace
844K Wheel Dozer and 990K Wheel Loader Power Train Axle Oil Cooler - Remove and Install
A Special Instruction Must be Followed when Installing Retaining-Rings on ELRT Control Valves {3030, 3083, 3157} A Special Instruction Must be Followed when Installing Retaining-Rings on ELRT Control Valves {3030, 3083, 3157}
A New Water Valve Is Used with the Cabs Air Conditioner on Certain Medium Wheel Loaders, Large Wheel Loaders Wheel Dozers, Soil Compactors, and Landfill Compactors {7320} A New Water Valve Is Used with the Cabs Air Conditioner on Certain Medium Wheel Loaders, Large Wheel Loaders Wheel Dozers, Soil Compactors, and Landfill Compactors {7320}
An Improved Backup Alarm is Used on Certain K-Series Small Wheel Loaders and B3 Series SSL/MTL/CTLs {1408, 7051} An Improved Backup Alarm is Used on Certain K-Series Small Wheel Loaders and B3 Series SSL/MTL/CTLs {1408, 7051}
844K Wheel Dozer and 990K Wheel Loader Power Train Gear Pump (Axle Oil Cooler) - Remove and Install
844K Wheel Dozer and 990K Wheel Loader Power Train Oscillating Axle (Rear) - Remove and Install
963K Track-Type Loader Machine Systems Piston Pump (Implement) - Remove and Install
An Improved Oil Cooler Drain Hose Routing Is Now Available On 963K Track-Type Loader {1380, 1386, 5057} An Improved Oil Cooler Drain Hose Routing Is Now Available On 963K Track-Type Loader {1380, 1386, 5057}
A New Water Valve Is Used with the Cabs Air Conditioner on Certain Large Wheel Loaders Wheel Dozers, Soil Compactors, and Landfill Compactors {7320} A New Water Valve Is Used with the Cabs Air Conditioner on Certain Large Wheel Loaders Wheel Dozers, Soil Compactors, and Landfill Compactors {7320}
Troubleshooting -7 Fuel Injector Not Responding Faults Excessively on Certain C9.3 Tier 4 Final {1290, 1920} Troubleshooting -7 Fuel Injector Not Responding Faults Excessively on Certain C9.3 Tier 4 Final {1290, 1920}
910K, 914K and 920K Compact Wheel Loaders Battery - Clean
C2.4 Tier 4 Final Engines for Caterpillar Built Machines Crankshaft - Install