Camshaft Gear - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Name | Qty |
A | 230-6284 | Camshaft Timing Pin | 1 |
B | 230-6283 | Crankshaft Timing Pin | 1 |
Start By:
- Remove the front cover if the front cover has not previously been removed. Refer to this Disassembly and Assembly Manual, "Front Cover - Remove and Install".
- Remove the idler gear if the idler gear has not previously been removed. Refer to this Disassembly and Assembly Manual, "Idler Gear - Remove and Install".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Make sure that the No. 1 cylinder is at the top center compression stroke. Refer to Testing and Adjusting, "Finding Top Center Position for No. 1 Piston".
Show/hide table
Illustration 1 g01229587 Typical example - Install Tooling (A) through the camshaft gear (2) at position (B). The camshaft gear will be locked in the correct position.
- Install Tooling (B) into the hole (C) in the housing. The crankshaft will be locked in the correct position.
- Remove Tooling (B) from the camshaft gear (2).
- Remove the setscrew (1) and the washer from the camshaft gear (2).
- Remove the camshaft gear (2) from the camshaft.
Note: Do not lose the key that is located in the camshaft for the camshaft gear (2).
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Inspect the camshaft gear (2) and the key in the camshaft for wear or damage.
Show/hide table
Illustration 2 g00954352 Typical example - Ensure that the marked teeth on the camshaft gear (2) are facing toward the front and that the key is installed in the camshaft. Install the camshaft gear (2) onto the camshaft. If necessary, tap the camshaft gear (2) with a soft hammer in order to seat the key in the keyway.
- Install the setscrew (1) and the washer onto the camshaft gear (2). Tighten the setscrew (1) to a torque of
95 N·m (70 lb ft) .
End By:
- Install the idler gear if this is the appropriate time. Refer to this Disassembly and Assembly Manual, "Idler Gear - Remove and Install".
- Install the front cover if this is the appropriate time. Refer to this Disassembly and Assembly Manual, "Front Cover - Remove and Install".
Caterpillar Information System:
C3.3 Industrial Engine Camshaft Bearings - Remove and Install
C3.3 Industrial Engine Engine Oil Pan - Remove and Install
C3.3 Industrial Engine Pistons and Connecting Rods - Remove
C3.3 Industrial Engine Pistons and Connecting Rods - Disassemble
C3.3 Industrial Engine Pistons and Connecting Rods - Assemble
C3.3 Industrial Engine Pistons and Connecting Rods - Install
C3.3 Industrial Engine Crankshaft Main Bearings - Remove
C3.3 Industrial Engine Crankshaft Main Bearings - Install - Crankshaft in Position
C3.3 Industrial Engine Crankshaft - Remove
C3.3 Industrial Engine Crankshaft - Install
C3.3 Industrial Engine Crankshaft Gear - Remove and Install
TH31 Well Servicing Transmissions Transmission and Torque Converter - Separate
C3.3 Industrial Engine Lifter Group - Remove and Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
3512B Oil Well Servicing Engine (ADEM III) Starting Motor System
CX31 On-Highway Transmission Power Train Transmission and Torque Converter - Separate
CX31 On-Highway Transmission Power Train Transmission and Torque Converter - Connect
3500B Engines Radiator Core - Remove
3500B Engines Radiator Core - Install
2006/01/02 A New Water Pump is Now Used {1361}
C3.3 Industrial Engine Crankshaft Front Seal - Remove
C3.3 Industrial Engine Crankshaft Pulley - Remove and Install
C3.3 Industrial Engine Valve Mechanism Cover - Remove and Install
C3.3 Industrial Engine Gear Group (Front) - Remove