Crankshaft Main Bearings - Remove
Start By:
- Remove the engine oil pan. Refer to this Disassembly and Assembly Manual, "Engine Oil Pan - Remove and Install".
- Remove the engine oil pump. Refer to this Disassembly and Assembly Manual, "Engine Oil Pump - Remove".
- Remove the flywheel housing in order to remove the rear main bearing with the crankshaft in position. Refer to this Disassembly and Assembly Manual, "Flywheel Housing - Remove and Install".
- Remove the crankshaft rear seal in order to remove the rear main bearing with the crankshaft in position. Refer to this Disassembly and Assembly Manual, "Crankshaft Rear Seal - Remove".
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Make sure that the main bearing caps (2) are marked for the location and direction for installation.
- Remove the setscrews (1) and the main bearing cap (2).
Show/hide table
Illustration 2 g00934803 - Remove the lower bearing shell (3) from the main bearing cap (2). Keep the respective bearing shell (3) and the main bearing cap (2) together for proper installation.
Show/hide table
Illustration 3 g00934767 - Push the upper bearing shell (4) from the opposite side of the bearing tab with a suitable tool. Carefully rotate the crankshaft while you push on the bearing shell (4). Remove the upper bearing shell (4) from the cylinder block. Keep all of the upper halves of the bearing shells (4) together in order to ensure proper installation.
- Repeat Step 2 through Step 4 for the remaining main bearings.
Note: Thrust washers (5) and (6) are installed onto one main bearing in order to limit crankshaft end play. These thrust washers are installed onto the No. 3 main bearing of the three cylinder engine.
Show/hide tableIllustration 4 g00934744 Typical example - Remove the lower half of the thrust washer (5) from each side of the appropriate main bearing cap.
Show/hide table
Illustration 5 g00947753 Typical example - Remove the upper half of the thrust washer (6) from each side of the appropriate main bearing in the cylinder block with a suitable tool. Carefully rotate the crankshaft while you push on the thrust washer (6). If necessary, move the crankshaft to the front or to the rear of the engine in order to loosen a tight thrust washer (6).
Show/hide table
Illustration 1 | g00947823 |
Note: The main bearings and the main bearing caps (2) must be installed in the same location when the engine is reassembled.
Caterpillar Information System:
C3.3 Industrial Engine Crankshaft Main Bearings - Install - Crankshaft in Position
C3.3 Industrial Engine Crankshaft - Remove
C3.3 Industrial Engine Crankshaft - Install
C3.3 Industrial Engine Crankshaft Gear - Remove and Install
TH31 Well Servicing Transmissions Transmission and Torque Converter - Separate
2006/01/02 A Different Grommet is Used to Secure the Engine Wiring Harness {1408}
C175-16 and C175-20 Engines for Caterpillar Built Machines Pistons and Connecting Rods - Disassemble
Reman Alternator Failures {1405} Reman Alternator Failures {1405}
C6.6 Engines for Caterpillar Built Machines Basic Engine
Installation of the Machine Security System (MSS) Universal Attachment Kit {7631, 7631} Installation of the Machine Security System (MSS) Universal Attachment Kit {7631, 7631}
The Valve Body May Crack on Certain Remanufactured Fuel Injectors{1290} The Valve Body May Crack on Certain Remanufactured Fuel Injectors{1290}
3126B and 3126E Truck Engines Vibration Damper
C3.3 Industrial Engine Pistons and Connecting Rods - Install
C3.3 Industrial Engine Pistons and Connecting Rods - Assemble
C3.3 Industrial Engine Pistons and Connecting Rods - Disassemble
C3.3 Industrial Engine Pistons and Connecting Rods - Remove
C3.3 Industrial Engine Engine Oil Pan - Remove and Install
C3.3 Industrial Engine Camshaft Bearings - Remove and Install
C3.3 Industrial Engine Camshaft Gear - Remove and Install
C3.3 Industrial Engine Lifter Group - Remove and Install
C175-16 and C175-20 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
3512B Oil Well Servicing Engine (ADEM III) Starting Motor System
CX31 On-Highway Transmission Power Train Transmission and Torque Converter - Separate
CX31 On-Highway Transmission Power Train Transmission and Torque Converter - Connect