Transmission and Torque Converter - Separate
分离步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 3     |
B     | 1P-2420     | 变速箱修复台     | 1     |
C     | 1U-9200     | 操纵杆滚轮起重机     | 1     |
开始:
- 如有必要,拆卸缓速器液压控制阀。 请参阅拆解和组装, "缓速器液压控制阀 - 拆卸和安装"。
- 如有必要,拆下控制歧管。 请参阅拆解和组装, "控制歧管 - 拆卸"。
Show/hide table
注意 |
---|
在进行检验、保养、测试、调整及维修产品期间,必须小心以确保装好排放出的油液。 在打开任何舱室或解体任何储有液体的部件之前,要准备好合适的容器收集液体。 有关收集和盛接 Cat 产品上油液的适用工具和用品,请参阅专门出版物, NENG2500, "代理商维修工具目录"。 按照当地法规和要求处置所有液体。 |
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。
注: 为便于安装,在所有管路、所有软管、所有线束组件及所有管子上做出识别标记。 插接好所有线路、软管和管路。 这将有助于防止液体泄漏和防止污染物进入系统。
- 如有配备,安装后 PTO 轴。
- 将适当的起吊设备和工具 (A) 安装到变速箱和变矩器 (1) 上。 将变速箱和变矩器安置在工具 (B) 上。 变速箱和变矩器 (1) 的重量约为 544 kg (1200 lb)。
Show/hide table
图 1 | g01229798 |
- 断开线束组件 (2) 和 (3) 。
Show/hide table
图 2 | g01229799 |
- 断开线束组件 (4) 。
Show/hide table
图 3 | g01229801 |
- 拆下螺栓 (5) 和端盖 (6) 。
Show/hide table
图 4 | g01229803 |
- 拆下磁性滤清器 (7) 和滤网 (8) 。
Show/hide table
图 5 | g01229809 |
- 拆下螺栓 (9) 和油底壳 (10) 。
Show/hide table
图 6 | g01229810 |
- 拆下管组件 (13) 和 (14) 。 拆下螺栓 (16) 和壳体 (15) 。 拆下螺栓 (11) 和泵 (12) 。
Show/hide table
图 7 | g01459033 |
注: 稍后拆卸螺栓 (12A) 。
- 拆下螺塞 (17) 和螺栓 (18) 。
注: 变矩器 (19) 不再固定至壳体。
Show/hide table
图 8 | g01229812 |
Show/hide table
图 9 | g01229813 |
- 将工具 (C) 和适当的起吊设备连接到工具 (A) 。 变矩器 (19) 的重量约为 204 kg (450 lb)。 从步骤8拆卸螺栓 (12A) 。 从变速箱 (21) 上拆卸螺栓 (20) 和变矩器 (19) 。
Show/hide table
图 10 | g01229817 |
Caterpillar Information System:
3512B Oil Well Servicing Engine (ADEM III) Starting Motor System
C175-16 and C175-20 Engines for Caterpillar Built Machines Crankshaft Main Bearings - Install
C3.3 Industrial Engine Lifter Group - Remove and Install
C3.3 Industrial Engine Camshaft Gear - Remove and Install
C3.3 Industrial Engine Camshaft Bearings - Remove and Install
C3.3 Industrial Engine Engine Oil Pan - Remove and Install
C3.3 Industrial Engine Pistons and Connecting Rods - Remove
C3.3 Industrial Engine Pistons and Connecting Rods - Disassemble
C3.3 Industrial Engine Pistons and Connecting Rods - Assemble
C3.3 Industrial Engine Pistons and Connecting Rods - Install
C3.3 Industrial Engine Crankshaft Main Bearings - Remove
C3.3 Industrial Engine Crankshaft Main Bearings - Install - Crankshaft in Position
CX31 On-Highway Transmission Power Train Transmission and Torque Converter - Connect
3500B Engines Radiator Core - Remove
3500B Engines Radiator Core - Install
2006/01/02 A New Water Pump is Now Used {1361}
C3.3 Industrial Engine Crankshaft Front Seal - Remove
C3.3 Industrial Engine Crankshaft Pulley - Remove and Install
C3.3 Industrial Engine Valve Mechanism Cover - Remove and Install
C3.3 Industrial Engine Gear Group (Front) - Remove
C3.3 Industrial Engine Gear Group (Front) - Install
C3.3 Industrial Engine Crankcase Breather - Remove and Install
CX31 On-Highway Transmission Power Train Torque Converter - Disassemble
CX31 On-Highway Transmission Power Train Torque Converter - Assemble