Fuel Filter Housing - Remove
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损並縮短部件使用寿命。 |
- 切断发动机的燃油供油。
Show/hide table
注意 在检查、保养、测试、调整及维修产品时,请小心确保盛接油液。 在打开任何舱室或拆卸任何含有油液的部件前,请准备好盛接液体用的适当容器。
- 将燃油滤清器壳体排入到合适的容器中以便进行保存或处理。
Show/hide table
图 1 g01050833 Show/hide table被弹簧力爆出的零件击中,会招致人员伤害。
确保穿上所有必要的保护装备。
遵照建议的程序,并使用所有建议的工具以释放弹簧力。
- 断开燃油压力传感器 (2) 。
- 断开软管组件 (3)。
- 拆下盖 (1)。
Show/hide table
图 2 g01050834 - 断开管组件 (6)。
- 卸下螺栓 (5)。
- 将适当的起吊设备连在燃油滤清器壳体 (4) 上。 燃油滤清器壳体 (4) 的重量约为
30 kg (66 lb) 。 拆下燃油滤清器壳体 (4)。
Caterpillar Information System:
G3304 and G3306 Engines Crankshaft - Remove
3406C Marine Auxiliary Generator Set Plate Locations and Film Locations
G3304 and G3306 Engines Camshaft Bearings - Install
G3304 and G3306 Engines Camshaft Bearings - Remove
C11, C13 and C15 On-highway Engines 0105-04 Intake Manifold Air Temperature voltage low (38)
C11, C13 and C15 On-highway Engines 0105-03 Intake Manifold Air Temperature voltage high (38)
Bench Test Procedure for Hydraulic Piston Pumps{5070} Bench Test Procedure for Hydraulic Piston Pumps{5070}
G3500 Engines MID 018 - CID 0523 - FMI 11 No A/F Ratio Engine Speed Sensor **Shutdown**
G3304 and G3306 Engines Cylinder Liner - Install
C3.3 Industrial Engine Engine Warm-up
G3500 Engines MID 018 - CID 0550 - FMI 02 Noisy or Loss of Oxygen Signal
G3520C and G3520E Generator Set Engines Crankshaft - Install
3500 Engines Fuel Filter Housing - Install
G3304 and G3306 Engines Crankshaft - Install
G3520C and G3520E Generator Set Engines Piston and Connecting Rods - Remove
G3520C and G3520E Generator Set Engines Piston and Connecting Rods - Install
2003/06/01 Improved Radiator for the Generator Set Engine {1353}
G3500 Engines MID 018 - CID 0551 - FMI 01 Oxygen Sensor not connected to buffer
G3500 Engines MID 018 - CID 0552 - FMI 11 Engine Speed present during an O2 calibration
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Oil Bypass Valve - Remove and Install
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Flywheel Telemetry - Calibrate
G3520C and G3520E Generator Set Engines Cylinder Liner - Install
3508C, 3512C and 3516C Marine Engines Camshaft Bearings - Remove
Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383} Replacing the Convection Jacket Water Heaters with a Recirculating Jacket Water Heater on 3500 Engines{1383}