Cylinder Head - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 6V-6640 | Sealant | - |
B | - | Guide Stud (M16 x 2.0 x 200 mm) |
2 |
C | 8T-3052 | Degree Wheel | 1 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Apply Tooling (A) to cup plugs (15). Install the cup plugs in the cylinder head.
- Install pipe plugs (15) in the cylinder head.
- Install the O-rings on plug assemblies (13) and plug assemblies (14). Install the plug assemblies in the cylinder head.
- Thoroughly clean the mating surfaces of the cylinder head and the cylinder block.
- Install Tooling (B) in the cylinder block.
- Install a new cylinder head gasket assembly on the cylinder block.
Show/hide table
Illustration 2 g01140918 - Attach a suitable lifting device to cylinder head (10). The weight of cylinder head (10) is approximately
104 kg (228 lb) . Position the cylinder head on Tooling (B). - Apply clean engine oil to the threads of cylinder head bolts (11) and under the bolt head. Install cylinder head bolts (11). Remove Tooling (B). Install the remaining cylinder head bolts.
Show/hide table
Illustration 3 g01140758 - Tighten the cylinder head bolts according to the following procedure:
- In a numerical sequence, tighten bolts 1 through 26 to a torque of
130 ± 15 N·m (96 ± 11 lb ft) . - In a numerical sequence, tighten bolts 1 through 26 to a torque of
130 ± 15 N·m (96 ± 11 lb ft) . - In a numerical sequence, tighten bolts 1 through 26 for an additional 90 ± 5 degrees (1/4 turn).
Note: If Tooling (C) is not used, place an index mark on the bolt and the cylinder head.
- Completely loosen bolts 1 through 26.
- In a numerical sequence, tighten bolts 1 through 26 to a torque of
130 ± 15 N·m (96 ± 11 lb ft) . - In a numerical sequence, tighten bolts 1 through 26 to a torque of
130 ± 15 N·m (96 ± 11 lb ft) . - In a numerical sequence, tighten bolts 1 through 26 for an additional 90 ± 5 degrees (1/4 turn).
Note: If Tooling (C) is not used, place an index mark on the bolt and the cylinder head.
- In a numerical sequence, tighten bolts 27 through 31 to a torque of
28 ± 75 N·m (20 ± 5 lb ft) .
Show/hide tableIllustration 4 g01027265 - In a numerical sequence, tighten bolts 1 through 26 to a torque of
- Install tube assembly (9) to cylinder head (10).
Show/hide table
Illustration 5 g01027299 - Connect harness assembly (7) and harness assembly (8) for the oil temperature sensors.
- Install air inlet heater relay (5).
- Connect injection actuation pressure sensor (6).
Show/hide table
Illustration 6 g00976251 - Connect fuel return tube assembly (4).
- Connect inlet air pressure sensor (2).
- Connect inlet air temperature sensor (3).
- Connect coolant temperature sensor (1).
Show/hide table
Illustration 1 | g01141531 |
End By:
- Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and Install".
- Install the oil filter base. Refer to Disassembly and Assembly, "Oil Filter Base - Remove and Install".
- Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base - Remove and Install".
- Install the aftercooler. Refer to Disassembly and Assembly, "Aftercooler - Install".
- Install the heat exchanger. Refer to Disassembly and Assembly, "Heat Exchanger - Install".
- Install the exhaust manifold. Refer to Disassembly and Assembly, "Exhaust Manifold - Remove and Install".
- Install the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Install".
- Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Install".
- Install the rocker arm and shaft. Refer to Disassembly and Assembly, " Rocker Arm and Shaft - Remove and Install".
- Install the valve cover base. Refer to Disassembly and Assembly, " Valve Mechanism Cover Base - Remove and Install".
Caterpillar Information System:
UPS 250, UPS 300, UPS 500, UPS 600, UPS 750 and UPS 900 Uninterruptible Power Supply Component Location - Cabinet (SMS)
EMCPII+ for Gas Engines GSC CID 0566 - FMI 07 (for Engine with EIS)
EMCPII+ for Gas Engines GSC CID 0566 - FMI 07 (for Engine with ECM)
C-10, C-12, C-15 and C-16 Industrial Engines Engine Pressure Sensor Open or Short Circuit - Test
EMCPII+ for Gas Engines GSC CID 0447 - FMI 12 (for Engine with EIS)
EMCPII+ for Gas Engines GSC CID 0447 - FMI 12 (for Engine with ECM)
EMCPII+ for Gas Engines GSC CID 0445 - FMI 12 (for Engine with EIS)
3500B and 3500C Marine Engines Camshaft
EMCPII+ for Gas Engines GSC CID 0445 - FMI 12 (for Engine with ECM)
EMCPII+ for Gas Engines GSC CID 0444 - FMI 12 (for Engine with EIS)
EMCPII+ for Gas Engines GSC CID 0444 - FMI 12 (for Engine with ECM)
EMCPII+ for Gas Engines GSC CID 0441 - FMI 12 (for Engine with EIS)
G3500B Engines Fuel Lines
3034 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove - Fractured Connecting Rod
G3500 Engines Junction Box
3500B Marine Engines Engine Speed/Timing Sensor - Calibrate
3412 Generator Set Engines Disconnect Switch
3034 Engine for Caterpillar Built Machines Pistons and Connecting Rods - Remove - Serrated Connecting Rod
3034 Engine for Caterpillar Built Machines Crankshaft - Install
G3500B Engines Vibration Damper
EMCPII+ for Gas Engines Engine/Generator Programming OP5-0
3500 Industrial Engines Stub Shaft (Front)
3044C Industrial Engine and Engines for Caterpillar Built Machines Engine Design
C11, C13 and C15 On-highway Engines Excessive Black Smoke