Speed Control Valve - Disassemble - MP324
Start By:
- Remove the speed control
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
- Remove bolts (2) and remove plate (1) (If Equipped). Remove bolts (4). Remove manifold (3).
Show/hide table
Illustration 2 g03678866 - Remove bolt (5) and remove pilot valve assembly (6). There are four bolts in total.
Show/hide table
Illustration 3 g03678867 - Remove two screws (7). Remove cap (9) and O-ring seal (8).
Show/hide table
Illustration 4 g03678869 - Remove O-ring seals (10). There are four O-ring seals in total.
Show/hide table
Illustration 5 g03678871 - Remove two screws (11).
Show/hide table
Illustration 6 g03678873 - Remove check valve (13) and remove O-ring seal (12).
Show/hide table
Illustration 7 g03678875 Relief Valve and Manifold Assembly - Remove plug (14) and O-ring seal (15). Remove plug (16) and O-ring seal (17). There are four plugs and O-ring seals in total. Remove screw (18) There are eight screws in total. Remove plugs (22), O-ring seals (20), and check valve (19). Remove relief valve (21) and O-ring seal (not shown).
Show/hide table
Illustration 8 g03678877 - Remove six bolts (23) and remove sequence valve assembly (24).
Show/hide table
Illustration 9 g03678878 - Remove six O-ring seals (25). Remove five screws (26). Remove two plugs (27). Remove O-ring seals (not shown) from plugs (27).
Show/hide table
Illustration 10 g03678879 - Remove four bolts (28) and remove intensifier valve assembly (29).
Show/hide table
Illustration 11 g03678880 - Remove 14 screws (33). Remove plug (30), O-ring seal (31), and check valve (32). There are four plugs, O-ring seals, and check valves in total.
Show/hide table
Illustration 12 g03678882 Show/hide tableIllustration 13 g03678884 - Remove four bolts (35) and cover (34). Remove O-ring seals (36), (37), (38), and backup rings (39), (40), (41) and (42).
Show/hide table
Illustration 14 g03678886 - Remove 15 O-ring seals (46). Remove 12 screws (47). Remove cap (45), O-ring seal (44), and check valve (43). Repeat for the remaining cap assembly. Remove check valves (48).
Show/hide table
Illustration 1 | g03677990 |
Caterpillar Information System:
312F and 313F Excavators Monitoring System
Hydraulic Thumbs Stop - Inspect/Replace
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System One-Way/One or Two Pump - Electric Control
314E CR and 314E SR Excavator Systems Cylinder (Blade) - If Equipped
826K Landfill Compactor, 825K Soil Compactor and 824K Wheel Dozer Engine Supplement Air Cleaner - Remove and Install
M316C Excavator Machine System Auxiliary Valve and Lines
M316C Excavator Machine System Window Wiper
M316C Excavator Machine System Operator Console
M316C Excavator Machine System Fan Guard
Command for Underground Customer Requirements {7605} Command for Underground Customer Requirements {7605}
349F and 352F Excavators Engine Supplement Exhaust Elbow - Remove and Install - Clean Emissions Module
CTV15, CTV20, CTV30 and CTV40 Clamshell Grapple/Verticle Cylinders Hydraulic Cylinder
M316C Excavator Machine System Control Valve (Main)
M316C Excavator Machine System Relief Valve (Main)
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Hydraulic Cylinder - Disassemble
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Hydraulic Cylinder - Assemble
Installation Procedure for the 443-7976 Control Gp on Certain Hydraulic Excavators {1931, 7600} Installation Procedure for the 443-7976 Control Gp on Certain Hydraulic Excavators {1931, 7600}
2013/08/27 A Rework Procedure to Replace the Adjustment Screw on Certain B20 Hammers {6333}
2013/08/23 The Design of the 391-4038 Head Allows for Alignment of the Bore of the Sleeve with the Bore of the Bushings on H75E s Hammers {6333}
349F and 352F Excavators Engine Supplement Diesel Exhaust Fluid Lines - Remove and Install - Clean Emissions Module
349F and 352F Excavators ECM - Replace
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Speed Control Valve - Assemble - MP324
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Two-Way/One Pump - Electric Control
Installation Procedure for the 443-7977 Valve Wiring Gp on Certain Hydraulic Excavators{1408, 5734} Installation Procedure for the 443-7977 Valve Wiring Gp on Certain Hydraulic Excavators{1408, 5734}