ECM - Replace
在更换 ECM 之前,确保更换是必需要做的操作。 ECM 不太可能是故障的原因。 务必检查并确认 ECM 标有 "+ Battery(蓄电池正极)"的所有触点上有电。
注: 配置软件损坏或软件不正确可能会导致 ECM 报告错误的诊断代码。 更换 ECM 前,向 ECM 中闪存正确的配置软件,以确认故障与软件损坏无关。 请参阅故障诊断与排除, "ECM 软件 - 安装"。
步骤
- 将断路开关和钥匙起动开关转到断开位置。
- 从 ECM 上断开机器线束接头。
- 确认更换的 ECM 的零件号正确。
- 安装更换的ECM。
- 将机器线束与 ECM 相连。
- 将断路开关和钥匙起动开关转到接通位置。
- 如有必要,使用 Cat® 电子技师 (Cat ET) 维修工具安装配置软件。 请参阅本手册中的测试和调整, "ECM(Electronic Control Module,电子控制模块)- 闪存编程"一节。
- 确认 ECM 正常工作。
Caterpillar Information System:
349F and 352F Excavators Engine Supplement Diesel Exhaust Fluid Lines - Remove and Install - Clean Emissions Module
2013/08/23 The Design of the 391-4038 Head Allows for Alignment of the Bore of the Sleeve with the Bore of the Bushings on H75E s Hammers {6333}
2013/08/27 A Rework Procedure to Replace the Adjustment Screw on Certain B20 Hammers {6333}
Installation Procedure for the 443-7976 Control Gp on Certain Hydraulic Excavators {1931, 7600} Installation Procedure for the 443-7976 Control Gp on Certain Hydraulic Excavators {1931, 7600}
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Hydraulic Cylinder - Assemble
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Hydraulic Cylinder - Disassemble
M316C Excavator Machine System Relief Valve (Main)
M316C Excavator Machine System Control Valve (Main)
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Speed Control Valve - Disassemble - MP324
312F and 313F Excavators Monitoring System
Hydraulic Thumbs Stop - Inspect/Replace
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System One-Way/One or Two Pump - Electric Control
MP318, MP324, MP332, MP345 and and MP365 Multi-Processors and Jaws Speed Control Valve - Assemble - MP324
349E, 349F and 352F Excavators and 349E MHPU Mobile Hydraulic Power Unit Tool Control System Two-Way/One Pump - Electric Control
Installation Procedure for the 443-7977 Valve Wiring Gp on Certain Hydraulic Excavators{1408, 5734} Installation Procedure for the 443-7977 Valve Wiring Gp on Certain Hydraulic Excavators{1408, 5734}
326F, 329F and 330F Excavators Machine Systems Swing Cushion Valve - Remove and Install
Procedure to Install 443-0252 Connecting Lines Gp {5057} Procedure to Install 443-0252 Connecting Lines Gp {5057}
Procedure to Install 443-0253 Connecting Lines Gp {5057} Procedure to Install 443-0253 Connecting Lines Gp {5057}
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
Procedure to Install 443-0254 Connecting Lines Group {5057} Procedure to Install 443-0254 Connecting Lines Group {5057}
349F and 352F Excavators Sensor Signal (PWM) - Test
Procedure to Install 443-0256 Connecting Lines Group {5057} Procedure to Install 443-0256 Connecting Lines Group {5057}
Procedure to Install 444-6448, 444-8962 Coupler Lines Groups on Certain 950H and 962H Wheel Loaders{0679, 5057, 5066, 5133, 6129} Procedure to Install 444-6448, 444-8962 Coupler Lines Groups on Certain 950H and 962H Wheel Loaders{0679, 5057, 5066, 5133, 6129}
326F, 329F and 330F Excavators Machine Systems Swing Cushion Valve - Disassemble - Fine Swing Solenoid