Control Manifold - Install
Installation Procedure
Show/hide table
| Required Tools | |||
| Tool | Pt. No. | Description | Qty |
| A | 4C-6486 | Stand | 4 |
| 8S-7641 | Tube | 2 | |
| 8S-7621 | Tube | 2 | |
| 8S-7625 | Collar | 1 | |
| 8S-8048 | Saddle | 4 | |
| 8S-7615 | Pin | 4 | |
| 189-0411 | Shackle As | 1 | |
| - | Pipe (51 mm (2 inch) OD) | 1 | |
| B | 1U-9759 | Jack Stand Gp | 1 |
Note: Inspect all O-ring seals for wear or for damage. Replace the components, if necessary.
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contamination of the hydraulic system with foreign material will reduce the service life of the hydraulic system components. To prevent contaminants from entering the hydraulic system, always plug or cap the lines, fittings, or hoses as they are disconnected. Cover any disassembled components and clean them properly before assembly. Clean the hydraulic system properly after any major component exchange or especially after a component failure, to remove any contamination. |
- Position control manifold (9) on the work tool. Fasten control manifold (9) in place with bolts (13). Tighten the bolts to a torque of 14 ± 3 N·m (10 ± 2 lb ft).
Show/hide table
 | |
| Illustration 1 | g01015286 |
- Install the O-ring seals. Install hose assembly (1) through hose assembly (8) on control manifold (9). Install hose assemblies (11) and (12) on the control manifold.
Show/hide table
 | |
| Illustration 2 | g01015191 |
Show/hide table
 | |
| Illustration 3 | g01015276 |
- Connect harness assemblies (10) .
- Remove the work tool from Tooling (A) and (B) .
Caterpillar Information System:
SW45 and SW60 Wheel Saws Control Manifold - Disassemble
SW45 and SW60 Wheel Saws Control Manifold - Assemble
SW45 and SW60 Wheel Saws Bearing - Remove and Install
G3500B Engines Engine Protective Devices - Check
SW45 and SW60 Wheel Saws Wheel Saw Drum - Remove and Install
2003/09/22 Improved Air Cleaner Bracket for the 302.5 and 303.5 Mini Hydraulic Excavator {1051}
321C LCR Excavator Machine Systems Swing Motor - Install
321C LCR Excavator Machine Systems Swing Motor - Remove
321C LCR Excavator Machine Systems Shuttle Valve - Install - Auxiliary Control
321C LCR Excavator Machine Systems Shuttle Valve - Remove - Auxiliary Control
322C Excavator Safety Messages - Arrangement I
325C and 325C L Excavator Hydraulic System Oil Sample - Obtain
SW45 and SW60 Wheel Saws Control Manifold - Remove
325D and 329D Excavators and 325D Material Handler Machine System Specifications Track
330C Material Handler Operation
C11 and C13 Engines for Caterpillar Built Machines Gear Group (Front) - Remove
3126B Engines for 322C, 325C, and M325C Excavators and for the 325C Mobile Hydraulic Power Unit Diagnostic Codes
330C Forest Machine Machine System Specifications Track
C11 and C13 Engines for Caterpillar Built Machines Gear Group (Front) - Install
345B Series II Material Handler Hydraulic System Oil Sample - Obtain
345B Series II Material Handler Swing Drive Oil Sample - Obtain
345B Series II Material Handler Engine Oil Sample - Obtain
345B Series II Material Handler Maintenance Interval Schedule
321C CR Excavator Engine Supplement Aftercooler - Remove and Install