Balancer Group - 3114 Engine Only
Show/hide table
图 1 | g00598058 |
前视图 |
Show/hide table
图 2 | g00598093 |
顶视图 |
(1) 曲轴齿轮
(2) 机油泵惰轮
(3) 机油泵壳体
(4) 从支架顶面到套筒顶部的距离 ... 5.0 ± 0.5 mm (0.20 ± 0.02 in)
(5) 正时标记
转动曲轴至 1 缸活塞压缩行程的 1 号活塞上止点位置的时间。 将平衡器齿轮 (11) 上的正时标记与机油泵体上的孔 (6) 对齐。
(6) 机油泵体
(7) 机油泵传动齿轮
(8) 后支架
- 孔径 ... 48.540 ± 0.025 mm (1.9110 ± 0.0010 in)
- 平衡轴直径 ... 48.40 ± 0.02 mm (1.906 ± 0.001 in)
(9) 中心支架
- 孔径 ... 51.561 ± 0.020 mm (2.0300 ± 0.0008 in)
- 平衡轴直径 ... 48.40 ± 0.02 mm (1.906 ± 0.001 in)
注: 中心支架中的轴承必须与支架的前端面平齐。
(10) 机油泵壳体
- 孔径 ... 48.540 ± 0.025 mm (1.9110 ± 0.0010 in)
- 平衡轴直径 ... 48.40 ± 0.02 mm (1.906 ± 0.001 in)
(11) 平衡器齿轮
- 将齿轮加热至以下温度以进行安装。 不要用喷枪。 ... 315 °C (599 °F)
Show/hide table
图 3 | g00598120 |
A-A 视图 |
(12) 止推销
- 每端直径 ... 5.89 ± 0.13 mm (0.232 ± 0.005 in) (B) 对边距离 ... 6.86 ± 0.03 mm (0.270 ± 0.001 in)
(13) 扣环
(14) 板
(15) 隔离器
Caterpillar Information System:
G3500 Engines Gas Pressure Regulator - Assemble
3126B Marine Engine Alternator and Regulator
G3500 Engines Gas Pressure Regulator - Disassemble
3126B Marine Engine Alternator and Regulator
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Remove - 3003 Engines
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Rocker Shaft and Pushrod - Install - 3003 Engine
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 441 FMI 12 Oil Step Relay Failed - Test
G3500 Engines Gas Pressure Regulator - Install - High Pressure
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 336 FMI 2 Switch (Engine Control) Incorrect Signal - Test
345B Excavator and 345B Material Handler Machine System Specifications Solenoid Valve (Counterweight Control)
G3500 Engines Gas Pressure Regulator - Remove - High Pressure
G3500 Engines Gas Pressure Regulator - Install - Low Pressure
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 444 FMI 12 Starting Motor Relay Failed - Test
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 445 FMI 12 Run Relay Failed - Test
G3500 Engines Fuel Control Valve - Remove and Install
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 446 FMI 12 Air Shutoff Relay Failed - Test
G3500 Engines Service Meter - Remove and Install
3126B Marine Engine Electric Starting Motor
G3500 Engines Cylinder Head - Disassemble
Electronic Modular Control Panel II (EMCP II) For PEEC Engines CID 447 FMI 12 Fuel Control Relay Failed - Test
3126B Marine Engine Electric Starting Motor
3126B Marine Engine Electric Starting Motor
3500B Engines and 3500 Engines with EUI Option Prelubrication System
3126B Marine Engine Electric Starting Motor