Fuel Ratio Control
Show/hide table
Illustration 1 | g00295799 |
(1) 7W-2826 Spring
- Length under test force ... 13.59 mm (.535 inch)
- Test force ... 77.40 ± 2.32 N (17.4 ± .5 lb)
- Free length after test ... 32.56 mm (1.282 inch)
- Outside diameter ... 35.12 mm (1.383 inch)
- Color code ... two red stripes
- Test force ... 77.40 ± 2.32 N (17.4 ± .5 lb)
(2) 7W-2828 Spring
- Length under test force ... 37 mm (1.46 inch)
- Test force ... 77.40 ± 2.32 N (17.4 ± .5 lb)
- Free length after test ... 46.4 mm (1.83 inch)
- Outside diameter ... 24.45 mm (.963 inch)
- Color code ... two yellow stripes
- Test force ... 77.40 ± 2.32 N (17.4 ± .5 lb)
(3) 8N-5765 Spring
- Length under test force ... 24 mm (.94 inch)
- Test force ... 22.25 ± 4 N (5 ± .9 lb)
- Free length after test ... 80.5 mm (3.17 inch)
- Outside diameter ... 37.57 mm (1.479 inch)
- Color code ... two pink stripes
- Test force ... 22.25 ± 4 N (5 ± .9 lb)
(4) Bolts
- Tighten the bolts to the following torque. ... 9 ± 3 N·m (80 ± 27 lb in)
(5) 9N-1754 Spring
- Length under test force ... 12.0 mm (.47 inch)
- Test force ... 6.22 ± 0.44 N (1.398 ± .099 lb)
- Free length after test ... 17.5 mm (.69 inch)
- Outside diameter ... 4.57 mm (.180 inch)
- Color code ... N/A
- Test force ... 6.22 ± 0.44 N (1.398 ± .099 lb)
Caterpillar Information System:
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
G3612 and G3616 Engines Engine Timing Procedures
C-10 and C-12 Truck Engines Rear Power Take-Off (RPTO)
G3612 and G3616 Engines Governor Adjustment Procedure
3406C (PEEC III) Truck Engine Engine Support (Front)
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3600 and C280 Diesel Engine Fluids Recommendations Heavy Fuel Oil
3406C Engines for Caterpillar Built Machines Exhaust Manifold Shield
G3612 and G3616 Engines Choke Trim
3176C and 3196 Engines for Caterpillar Built Machines Cylinder Block
C-10 and C-12 Truck Engines Boost Pressure Sensor
G3612 and G3616 Engines Governor Adjustment Procedure
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3306B Industrial Engine Troubleshooting
3306B Industrial Engine Electric Starting Motor - Remove and Install
3306B Industrial Engine Alternator - Remove and Install
3306B Industrial Engine Fuel Injection Lines
G3612 and G3616 Engines Engine Supervisory System
Electronic Modular Control Panel II (EMCP II) for EUI Engines Service Record
G3612 and G3616 Engines Ignition System
3406C (PEEC III) Truck Engine Manual Shutoff
3306B Industrial Engine Gear Group (Front)
3306B Industrial Engine Fuel System
3406C (PEEC III) Truck Engine Governor and Fuel Pump Drive