Inlet and Exhaust Valves - Remove and Install
拆卸步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 5S-1330     | 气门弹簧压缩器     | 1     |
B     | 8S-2263     | 气门弹簧测试仪     | 1     |
开始:
- 拆卸缸盖。 请参考解体与组装, "缸盖 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 使用工具 (A) 压缩气门弹簧 (2) ,然后拆下气门锁片 (1) 。
Show/hide table
图 1 | g00490614 |
- 拆下工具 (A) 、rotocoil 密封圈、气门弹簧和气门杆油罩。 从缸盖上拆下气门。 为了便于安装,在气门上作出识别标记。
- 用工具 (B) 检查气门弹簧力。 有关气门弹簧的信息,请参考技术参数, "缸盖气门"。
Show/hide table
图 2 | g00490682 |
- 对于其余的进气门和排气门,进行第 1 至 3 步。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件名称     | 数量     |
A     | 5S-1330     | 气门弹簧压缩器     | 1     |
B     | 5S-1322     | 气门锁片插入器     | 1     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 用清洁的发动机机油润滑进气门和排气门。 将进气门和排气门安装到缸盖中原来的位置。
- 将气门 (3) 、油罩 (4) 、气门弹簧 (2) 和 rotocoil 密封圈 (1) 安装到缸盖中。
Show/hide table
图 3 | g00508681 |
- 使用工具 (A) 压缩气门弹簧 (2) 。 使用工具 (B) 将气门锁片 (5) 安装到气门杆上。
Show/hide table
图 4 | g00490777 |
- 小心拆下工具 (A) 。 用软面锤敲击气门顶部,以便确保气门锁片安装正确。
Show/hide table
当松开气门弹簧压缩器时,气门锁片可能会从气门中弹出。 确保气门锁片正确安装在气门杆上。 为了帮助避免人员伤害,在安装气门时,始终应避开气门锁片和气门弹簧的前方。 |
- 对于其余的进气门和排气门,重复第 3 至 4 步。
End By: 安装缸盖。 请参考 解体与组装, "缸盖 - 拆卸和安装"。
Caterpillar Information System:
3600 and C280 Diesel Engine Fluids Recommendations Heavy Fuel Oil
3406C Engines for Caterpillar Built Machines Exhaust Manifold Shield
G3612 and G3616 Engines Choke Trim
3176C and 3196 Engines for Caterpillar Built Machines Cylinder Block
C-10 and C-12 Truck Engines Boost Pressure Sensor
G3612 and G3616 Engines Governor Adjustment Procedure
3126 Truck Engine Injection Actuation Pressure Sensor
3126 Truck Engine Boost Pressure Sensor
3306B Industrial Engine Governor
3406C Engines for Caterpillar Built Machines Exhaust Manifold
Electronic Modular Control Panel II (EMCP II) for EUI Engines Schematics and Wiring Diagrams
Electronic Modular Control Panel II (EMCP II) For MUI Engines Block Diagram of Generator Set Control
3406C (PEEC III) Truck Engine Engine Support (Front)
G3612 and G3616 Engines Governor Adjustment Procedure
C-10 and C-12 Truck Engines Rear Power Take-Off (RPTO)
G3612 and G3616 Engines Engine Timing Procedures
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3306B Industrial Engine Fuel Ratio Control
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3306B Industrial Engine Troubleshooting
3306B Industrial Engine Electric Starting Motor - Remove and Install
3306B Industrial Engine Alternator - Remove and Install
3306B Industrial Engine Fuel Injection Lines
G3612 and G3616 Engines Engine Supervisory System