Rear Power Take-Off (RPTO)
Show/hide table
Illustration 1 | g01437478 |
(2) Carrier bearing housing
(5) Bearing |
Show/hide table
Illustration 2 | g01437480 |
(1) Output shaft (PTO)
- Diameter of the output shaft (A) ...
60.245 ± 0.025 mm (2.3718 ± 0.0010 inch) - End play of the output shaft ...
0.97 ± 0.43 mm (0.038 ± 0.017 inch) - End play of the output shaft ...
(3) Carrier bearing
- The carrier bearing should be installed to the following depth (B) in the carrier bearing housing. ...
1.6 ± 0.5 mm (0.06 ± 0.02 inch) - When the engine is viewed from the rear, the split in the bearing should be located counterclockwise from the center of the top bolt at the following angle. ... 112 ± 10 degrees
(4) Drive gear
- Inside diameter of the drive gear ...
60.320 ± 0.025 mm (2.3750 ± 0.0010 inch) - The clearance between the output shaft (1) and the drive gear (4) ...
0.025 to 0.125 mm (0.0010 to 0.0050 inch) - The clearance between the output shaft (1) and the drive gear (4) ...
(6) Thrust washer
- Thickness of the thrust washer ...
4.690 ± 0.025 mm (0.1846 ± 0.0010 inch)
(7) Thrust plate
- Thickness of the thrust plate ...
6.75 mm (0.266 inch)
(8) Thrust washer
- Thickness of the thrust washer ...
4.690 ± 0.025 mm (0.1846 ± 0.0010 inch)
(9) Idler gear
- Inside diameter of the idler gear ...
88.90 ± 0.013 mm (3.500 ± 0.0005 inch)
(10) Seal
- Install the seal to the following depth. ...
2.5 ± 0.5 mm (0.10 ± 0.02 inch)
Lubricate the sealing lip lightly with the lubricant that is being sealed.
Show/hide table
Illustration 3 | g01437483 |
(11) Bearing
- The relief groove in the bearing must line up with the relief grooves in the idler gear within the following value. ... 2 degrees
The bearing must not extend beyond either face of the idler gear.
Caterpillar Information System:
G3612 and G3616 Engines Governor Adjustment Procedure
3406C (PEEC III) Truck Engine Engine Support (Front)
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valves - Remove and Install
3600 and C280 Diesel Engine Fluids Recommendations Heavy Fuel Oil
3406C Engines for Caterpillar Built Machines Exhaust Manifold Shield
G3612 and G3616 Engines Choke Trim
3176C and 3196 Engines for Caterpillar Built Machines Cylinder Block
C-10 and C-12 Truck Engines Boost Pressure Sensor
G3612 and G3616 Engines Governor Adjustment Procedure
3126 Truck Engine Injection Actuation Pressure Sensor
3126 Truck Engine Boost Pressure Sensor
3306B Industrial Engine Governor
G3612 and G3616 Engines Engine Timing Procedures
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Guides - Remove and Install
3306B Industrial Engine Fuel Ratio Control
3304B and 3306B Engines for Caterpillar Built Machines Inlet and Exhaust Valve Seat Inserts - Remove and Install
3306B Industrial Engine Troubleshooting
3306B Industrial Engine Electric Starting Motor - Remove and Install
3306B Industrial Engine Alternator - Remove and Install
3306B Industrial Engine Fuel Injection Lines
G3612 and G3616 Engines Engine Supervisory System
Electronic Modular Control Panel II (EMCP II) for EUI Engines Service Record
G3612 and G3616 Engines Ignition System
3406C (PEEC III) Truck Engine Manual Shutoff