Heat Exchanger
Show/hide table
Illustration 1 | g03347129 |
Front view of engine |
Show/hide table
Specification for 290-3990 Sea Water Heat Exchanger Gp     | |||
Item     | Qty     | Part     | Specification Description     |
1     | 2     | 0S-1619 Bolt     | Use the following procedure in order to tighten the bolts: 1. Hand tighten bolt (1) through bolt (5) in a numerical sequence. 2. Again, final tighten bolt (1) through bolt (5) in a numerical sequence to standard torque.     |
2     | 1     | 0S-1590 Bolt     | |
3     | 2     | 0S-1590 Bolt     | |
4     | 2     | 0S-1591 Bolt     | |
5     | 4     | 8T-4835 Bolt     |
Show/hide table
Illustration 2 | g03347130 |
373-2563 Sea Water Heat Exchanger Gp |
Show/hide table
Item     | Qty     | Part     | Specification Description     |
6     | 10     | -     | Use the following procedure in order to tighten the bolt (6) : 1. Install guide studs, washers, and nuts in locations 5 and 6. Hand tighten bolt 1 through bolt 4 in the numerical sequence as shown in Illustration 2. Use minimum three incremental steps to tighten the bolts. 2. Remove the guide studs from locations 5 and 6. 3. Install the special spacers (7) in locations 5 and 6. 4. Tighten bolt 1 trough bolt 10 in the numerical sequence as shown in Illustration 2 to 115 ± 6 N·m (85 ± 4 lb ft).     |
7     | 2     | -     |
Caterpillar Information System:
C7.1 Engines for Caterpillar Built Machines Electronic Control System
2013/04/22 An Improved Oil Level Gauge Is Now Used on Certain C15 Generator Sets {1326}
336F and 340F Excavators Machine System Specifications Swing Gear and Bearing
C13, C15, and C18 Generator Set Engines Exhaust Manifold
C7.1 Engines for Caterpillar Built Machines Fuel Injection
C7.1 Engines for Caterpillar Built Machines Turbocharger - Inspect
C7.1 Engines for Caterpillar Built Machines Air Inlet and Exhaust System - Inspect
C7.1 Engines for Caterpillar Built Machines Air Inlet and Exhaust System
C7.1 Engines for Caterpillar Built Machines Basic Engine
C7.1 Engines for Caterpillar Built Machines Introduction
C18 Marine Propulsion Engines Cylinder Block
C7.1 Engines for Caterpillar Built Machines Compression - Test
C7.1 Engines for Caterpillar Built Machines Power Sources
C4.4 (Mech) Marine Generator Set MCS-3 Engine Crankcase Breather Element - Replace - Turbocharged Engines
C7.1 Engines for Caterpillar Built Machines Glossary of Electronic Control Terms
C4.4 (Mech) Marine Generator Set MCS-3 Maintenance Interval Schedule - Turbocharged Marine Generator Set Without Aftercooler
C175-16 Locomotive Engine Electronic Control Module (ECM)
C7.1 Engines for Caterpillar Built Machines Air in Fuel - Test
C4.4 (Mech) Marine Generator Set MCS-3 Severe Service Application
C7.1 Engines for Caterpillar Built Machines Fuel Injection Timing - Check
C4.4 (Mech) Marine Generator Set MCS-3 Engine Crankcase Breather - Replace - Turbocharged Engines
C280-16 Engine Product Description
C7.1 Marine Engine Fuel Priming Pump - Remove and Install
C280-16 Engine Refill Capacities