Engine Oil Pan
Show/hide table
Illustration 1 | g02882477 |
Show/hide table
Specification for 381-2057 Oil Pan Gp | |||
Item | Qty | Part | Specification Description |
- | 15 | 1A-2029 Bolt | Use the following procedure to tighten the bolts:
1. Tighten five bolts (11) first. 2. Then tighten the bolt (1) through bolt (10) in numerical sequence as shown in Illustration 1. |
12 | - | - | As required, apply Loctite RTV Silicone Clear or Permatex No.2 to the gasket joints, before assembly. |
13 | 2 | 3P-0654 O-Ring Seal | Lubricate the bore lightly with the fluid that is being sealed. |
14 | 1 | 4B-2363 Oil Drain Plug | Torque to |
Show/hide table
Illustration 2 | g03027819 |
Top front view |
Show/hide table
Item | Qty | Part | Specification Description |
15 | 50 | 5P-5855 Bolt | As required, apply green Loctite 290 after assembly. |
16 | 4 | 5P-5700 O-Ring Seal | Lubricate the bore lightly with the fluid that is being sealed. |
17 | 2 | 6V-4315 O-Ring Seal | Lubricate the bore lightly with the fluid that is being sealed. |
Caterpillar Information System:
Utilizing the Electric Power SpecSizer for Proper Generator Set Sizing{1404, 7002} Utilizing the Electric Power SpecSizer for Proper Generator Set Sizing{1404, 7002}
2012/03/19 A New Exhaust Manifold Center Section and Turbocharger Mounting Hardware Are Used on Certain C18 Industrial Engines {1059}
3512B and 3512C Petroleum Generator Set Engines Coolant Temperature Is High
2012/02/15 New Heat Shield Groups Are Used on Certain C15 and C18 Generator Sets {1067}
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Coolant Contains Oil
C175-16 Marine Propulsion Engines Prelubrication - Test
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Coolant Contains Fuel
3512C and 3516C Marine Auxiliary and Generator Set Engines Stator Winding Temperature - Test
C13, C15, and C18 Tier 4 Final Engines Electronic Service Tool Does Not Communicate
C13, C15, and C18 Tier 4 Final Engines Cat ET Service Error Identifiers
C13, C15, and C18 Tier 4 Final Engines Speed/Timing - Test
Extra O-ring Required for Water Pump Installation on Certain C15 On-Highway Truck Engines{1355, 1361, 1380, 1393} Extra O-ring Required for Water Pump Installation on Certain C15 On-Highway Truck Engines{1355, 1361, 1380, 1393}
C175-16 Generator Set Model View Illustrations
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Flash Program
3512C and 3516C Marine Auxiliary and Generator Set Engines Rotating Rectifier - Inspect/Test
C175-16 Marine Engine Fuel Priming Pump
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Configure
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Replace
3512B and 3512C Petroleum Generator Set Engines Coolant Temperature Is Low
C175-16 Marine Engine Engine Oil Filter Housing
C175-16 Marine Engine Engine Oil and Water Pump Drive
Using the 164-2691 Printer Group {0374, 0599, 0684, 5057} Using the 164-2691 Printer Group {0374, 0599, 0684, 5057}
168-7720 Ultrasonic Wear Indicator III Group{0374, 0599, 0729, 0787} 168-7720 Ultrasonic Wear Indicator III Group{0374, 0599, 0729, 0787}