Fuel Priming Pump
- Turn the fuel supply to the OFF position.
Show/hide table
Illustration 1 g02883202 - Disconnect hose assemblies (1) and (3). Disconnect harness assembly (2). Remove bolts (5). Remove fuel priming pump (4).
Show/hide table
NOTICE |
---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install fuel priming pump (5) in the reverse order of removal.
- Turn the fuel supply to the ON position.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Caterpillar Information System:
3512C and 3516C Marine Auxiliary and Generator Set Engines Rotating Rectifier - Inspect/Test
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Flash Program
C175-16 Generator Set Model View Illustrations
Extra O-ring Required for Water Pump Installation on Certain C15 On-Highway Truck Engines{1355, 1361, 1380, 1393} Extra O-ring Required for Water Pump Installation on Certain C15 On-Highway Truck Engines{1355, 1361, 1380, 1393}
3500C Marine Engines Engine Oil Pan
Utilizing the Electric Power SpecSizer for Proper Generator Set Sizing{1404, 7002} Utilizing the Electric Power SpecSizer for Proper Generator Set Sizing{1404, 7002}
2012/03/19 A New Exhaust Manifold Center Section and Turbocharger Mounting Hardware Are Used on Certain C18 Industrial Engines {1059}
3512B and 3512C Petroleum Generator Set Engines Coolant Temperature Is High
2012/02/15 New Heat Shield Groups Are Used on Certain C15 and C18 Generator Sets {1067}
Bench Test Procedure for Hydraulic Piston Pumps {5070} Bench Test Procedure for Hydraulic Piston Pumps {5070}
3512B, 3512C, and 3516B Petroleum Engines and Petroleum Generator Set Engines with Dynamic Gas Blending Coolant Contains Oil
C175-16 Marine Propulsion Engines Prelubrication - Test
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Configure
CX31-P600-C11I, CX31-P600-C13I, CX31-P600-C15I, CX31-P600-C18I and CX31-P600-C9I Petroleum Power Train Packages and CX31-P600 Petroleum Transmission Power Train Electronic Control System Electronic Control Module (ECM) - Replace
3512B and 3512C Petroleum Generator Set Engines Coolant Temperature Is Low
C175-16 Marine Engine Engine Oil Filter Housing
C175-16 Marine Engine Engine Oil and Water Pump Drive
Using the 164-2691 Printer Group {0374, 0599, 0684, 5057} Using the 164-2691 Printer Group {0374, 0599, 0684, 5057}
168-7720 Ultrasonic Wear Indicator III Group{0374, 0599, 0729, 0787} 168-7720 Ultrasonic Wear Indicator III Group{0374, 0599, 0729, 0787}
3500C Marine Engines Engine Oil Lines
C175-16 Marine Propulsion Engines Sensor Signal (Analog, Active) - Test
3512B and 3512C Petroleum Generator Set Engines Crankcase Pressure Is High
PMG3516 Power Module Product Description
PMG3516 Power Module Product Lifting