MID 116 - CID 1482 - FMI 03
产生此代码的情况:
当 ECM 检测到 10V 电源电压的电压高于正常电压时,会记录 CID 1482 FMI 03 维修代码。
下述原因可能会引起该诊断代码:
- 电源导线(799-WH)对蓄电池正极电路短路。
- 一个使用该电源的部件出现故障。
- ECM 出现故障。 这不太可能。
注: 确保 CID 1482 FMI 03 为现行状态。
测试步骤 1. 检查 ECM 上有无正确电压。
- 将断路开关和钥匙起动开关转到接通位置。
- 检查 ECM 接头上触针 J1-69 与触针 J1-70(接地)之间的电压。 使用 7X-1710 电缆表笔 测量该电压。 不要从 ECM 上断开机器线束。
预期结果:
电压为 10.0 ± 0.5 DCV。
结果:
- 确定 - 电压为 10.0 ± 0.5 DCV。 传感器电源电压正常。 确认诊断代码是否存在。 如果诊断代码仍然存在,则 ECM 出故障。 更换 ECM。
修复: ECM 不太可能会出现故障。 先退出此步骤,然后重新执行此步骤。 此外,还应重新检查该诊断代码是否处于激活状态。 如果没有找到该诊断代码的原因,则应更换 ECM。 请参阅本手册的测试和调整, "电子控制模块 (ECM) - 更换"一章。
停止
- 异常 - 电压大于 10.0 ± 0.5 DCV。 电源电压不正常。 转至测试步骤 2。
测试步骤 2. 检查线束是否对蓄电池电路短路。
- 将断路开关和钥匙起动开关转到接通位置。
- 从 ECM 上断开机器线束。
- 在 ECM 机器线束接头上,测量接头触点 J1-69 与机架接地之间的电阻。
预期结果:
电压值为 0.0 ± 0.5 DCV。
结果:
- 确定 - 电压为 0.0 ± 0.5 DCV。 电压正确。 ECM 出现故障。
修复: ECM 不太可能会出现故障。 先退出此步骤,然后重新执行此步骤。 此外,还应重新检查该诊断代码是否处于激活状态。 如果没有找到该诊断代码的原因,则应更换 ECM。 请参阅本手册的测试和调整, "电子控制模块 (ECM) - 更换"一章。
停止
- 异常 - 电压不是 0.0 ± 0.5 DCV。 电源电压不正常。
修复: 机器线束对蓄电池正极电路短路。 修理或更换机器线束。
停止
Caterpillar Information System:
793F and 797F Off-Highway Trucks Braking System MID 116 - CID 1482 - FMI 04
3406E and C15 Marine Engines Engine Speed/Timing Sensor - Clean/Inspect
3406E and C15 Marine Engines Engine Air Cleaner Element (Single Element) - Inspect/Clean/Replace
3406E and C15 Marine Engines Coolant Level - Check
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Transmission, SPN 1716 - FMI 9
3406E and C15 Marine Engines Plate Locations and Film Locations
C18 Generator Set Generator - Align
CT660 CX31 and CX31 HT On Highway Truck Power Train Electronic Control System Transmission, SPN 1716 - FMI 19
3406E and C15 Marine Engines Product Description
C15 Petroleum Engines Valve Mechanism Cover Base - Remove and Install
797F and 797F XQ Off-Highway Truck Braking System Gear Pump (Brake Cooling, Hoist)
Procedure for Replacing the Circuit Breaker Group on Certain Generator Sets{1420, 4461} Procedure for Replacing the Circuit Breaker Group on Certain Generator Sets{1420, 4461}
G3516 Engines Temperature Sensor
C175-16 Marine Engines Belts - Inspect/Adjust/Replace
C18 Generator Set Bearing - Remove and Install
C175-16 Petroleum Generator Set Engines Coolant (DEAC) - Change
C27 and C32 Engines for Caterpillar Built Machines Engine Oil Pressure Sensor
349F and 352F Excavators Quick Coupler Operation - Hydraulic Pin Grabber Quick Coupler (If Equipped)
C27 Petroleum Generator Set Engines Exhaust Balance Valve - Test
2011/04/15 Improved Registration Process for Retrofit Products {1000, 7000}
C27 Generator Set Engines ECM - Replace
C27 Petroleum Generator Set Engines NOx Reduction System (NRS) - Test
992K Wheel Loader Fuel Tank Cap Filter - Replace
UPSB220 Uninterruptible Power Supply Component Location