Camshaft Bearings - Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 6V-4077 | Camshaft Bearing Tool | 1 |
125-2739 (1) | Bearing Pilot | 1 | |
125-2740 (1) | Back Up Plate | 1 | |
125-2741 (1) | Bearing Sleeve | 1 | |
B | 8S-2241 | Camshaft Bearing Tool Group | 1 |
C | 5P-5247 | Hydraulic Puller(2) | 1 |
D | 8H-0684 | Ratchet Wrench | 1 |
Show/hide table
(1) | Alternate Tooling for camshaft bearings with a large diameter |
(2) | Do not exceed |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Install camshaft bearing (1) on Tooling (A).
Note: Tooling (B) can be used to install the camshaft bearings when the flywheel housing and the front housing have been removed.
Show/hide tableIllustration 2 g02108639 Rear View
(X) Location of camshaft bearing joints
(Y) Location of oil holes - Position camshaft bearing (1) and Tooling (A) in the bore.
Note: The camshaft bearing joint must be on the horizontal centerline of the bore. The upper oil hole must be 20 ± 5 degrees above the horizontal centerline of the bore. The lower oil hole of the camshaft bearing must be 20 ± 5 degrees below the horizontal centerline of the bore. The camshaft bearing joints must face the inside the cylinder block.
Show/hide tableIllustration 3 g00578349 - Install Tooling (C) on Tooling (A) and pull the camshaft bearing into the bore.
Note: Tooling (D) can be used in place of Tooling (C).
Show/hide table
Illustration 1 | g00578338 |
End By:
- Install the camshafts.
Caterpillar Information System:
C6.6 Generator Set CID 0003 FMI 06
C6.6 Generator Set CID 0003 FMI 05
C6.6 Generator Set CID 0003 FMI 02
3508, 3512 and 3516 Generator Set Engines Camshaft Bearings - Remove
C6.6 Generator Set CID 0002 FMI 06
C175-16 PETROLEUM ENGINES Connecting Rod Bearings - Remove and Install
C6.6 Generator Set CID 0002 FMI 05
C6.6 Generator Set CID 0002 FMI 02
C6.6 Generator Set CID 0001 FMI 06
C6.6 Generator Set CID 0001 FMI 05
C6.6 Generator Set CID 0001 FMI 02
C13, C15, and C18 Tier 4 Interim Engines Inlet Air Is Restricted
2010/01/14 New Communication Software for the PL1000T Is Now Used on Commercial Engines {7606, 7620}
Track, Track Roller, and Track Idler Cycle Times {4159, 4169, 4170, 4171, 4180} Track, Track Roller, and Track Idler Cycle Times {4159, 4169, 4170, 4171, 4180}
C6.6 Generator Set CID 0004 FMI 02
C6.6 Generator Set CID 0004 FMI 05
C6.6 Generator Set CID 0004 FMI 06
C6.6 Generator Set CID 0100 FMI 03
C6.6 Generator Set CID 0100 FMI 04
C6.6 Generator Set CID 0100 FMI 10
C6.6 Generator Set CID 0110 FMI 03
C6.6 Generator Set CID 0110 FMI 04
C6.6 Generator Set CID 0168 FMI 00
3508, 3512 and 3516 Generator Set Engines Crankshaft - Remove