Camshaft Bearings - Remove
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 6V-4077 | Camshaft Bearing Tool | 1 |
125-2739 (1) | Bearing Pilot | 1 | |
125-2740 (1) | Back Up Plate | 1 | |
125-2741 (1) | Bearing Sleeve | 1 | |
B | 8S-2241 | Camshaft Bearing Tool Group | 1 |
C | 5P-5247 | Hydraulic Puller(2) | 1 |
D | 8H-0684 | Ratchet Wrench | 1 |
Show/hide table
(1) | Alternate Tooling for camshaft bearings with a large diameter |
(2) | Do not exceed |
Start By:
- Remove the camshafts.
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Use the following steps to install Tooling (A).
- Install the pilot group in camshaft bearing (1) (not shown).
- Place the backup plate in position and ensure that camshaft bearing (1) (not shown) is between the two parts.
- Install the bolt that holds Tooling (A) together.
- Use the extensions to obtain the correct length for Tooling (A).
- Install the puller plate on the bolt and the flywheel housing or the front housing.
Note: Tooling (B) can be used to remove the camshaft bearings when the flywheel housing and the front housing have been removed.
Show/hide tableIllustration 2 g01208875 - Install Tooling (C) on Tooling (A). Pull camshaft bearing (1) from the cylinder block.
Note: Tooling (D) can be used in place of Tooling (C), if necessary.
Show/hide table
Illustration 1 | g01208871 |
Caterpillar Information System:
C6.6 Generator Set CID 0002 FMI 06
C175-16 PETROLEUM ENGINES Connecting Rod Bearings - Remove and Install
C6.6 Generator Set CID 0002 FMI 05
C6.6 Generator Set CID 0002 FMI 02
C6.6 Generator Set CID 0001 FMI 06
C6.6 Generator Set CID 0001 FMI 05
C6.6 Generator Set CID 0001 FMI 02
C13, C15, and C18 Tier 4 Interim Engines Inlet Air Is Restricted
C13, C15, and C18 Tier 4 Interim Engines Event Codes
C13, C15, and C18 Tier 4 Interim Engines Diagnostic Trouble Codes
3508, 3512 and 3516 Generator Set Engines Camshaft - Install
C13 and C15 Engines for Combat and Tactical Vehicles Accelerator Pedal (Throttle) Position Sensor Circuit - Test
C6.6 Generator Set CID 0003 FMI 02
C6.6 Generator Set CID 0003 FMI 05
C6.6 Generator Set CID 0003 FMI 06
3508, 3512 and 3516 Generator Set Engines Camshaft Bearings - Install
2010/01/14 New Communication Software for the PL1000T Is Now Used on Commercial Engines {7606, 7620}
Track, Track Roller, and Track Idler Cycle Times {4159, 4169, 4170, 4171, 4180} Track, Track Roller, and Track Idler Cycle Times {4159, 4169, 4170, 4171, 4180}
C6.6 Generator Set CID 0004 FMI 02
C6.6 Generator Set CID 0004 FMI 05
C6.6 Generator Set CID 0004 FMI 06
C6.6 Generator Set CID 0100 FMI 03
C6.6 Generator Set CID 0100 FMI 04
C6.6 Generator Set CID 0100 FMI 10