Engine Lifting Bracket - Remove and Install
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
A | 4C-9517 | Plug | 4 |
B | 185-5192 | Stud Protector | 4 |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Turn OFF the fuel supply to the engine.
Show/hide table
Illustration 1 g01282900 - Remove the protective cover from the lifting brackets. Mark the location of the lifting brackets.
- Remove tube assemblies (1). Use Tooling (A) to plug the openings in order to prevent debris from entering the fuel system.
- Remove nuts (3).
- Remove lifting bracket (2).
Note: Store the lifting brackets in a clean dry place. Do not install the lifting brackets until it is necessary to lift the engine.
- Install Tooling (B) on each cylinder head stud.
Show/hide table
Required Tools | |||
Tool | Part Number | Part Description | Qty |
B | 185-5192 | Stud Protector | 4 |
C | 5P-3931 | Anti-Seize Compound | - |
Show/hide table
NOTICE |
---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
- Remove Tooling (B) from each cylinder head stud.
- Install the engine lifting brackets on a 3606 Engine between the following cylinders:
- Number 1 Cylinder and Number 2 Cylinder
- Number 5 Cylinder and Number 6 Cylinder
- Install the engine lifting brackets on a 3608 Engine between the following cylinders:
- Number 1 Cylinder and Number 2 Cylinder
- Number 7 Cylinder and Number 8 Cylinder
- Apply Tooling (C) on the threads of the cylinder head studs.
Show/hide table
Illustration 2 g01282900 - Put engine lifting bracket (2) in position on the cylinder head studs. Install nuts (3). Tighten the nuts to a torque of
2150 ± 250 N·m (1590 ± 185 lb ft) .Note: The brackets must be installed so that the pin holes in the clevis are in a horizontal plane.
- Install tube assemblies (1).
- Turn ON the fuel supply.
Caterpillar Information System:
C6.6 Engines for Caterpillar Built Machines Fuel Priming Pump
C32 Power Module Engine Valve Lash - Inspect/Adjust
390F Excavator Machine Systems Travel Motor - Disassemble
C175-16 Locomotive Engine Engine Speed Sensor
2006/07/03 A New Speed-Timing Sensor is Available {1912}
325D and 329D Excavators and 325D Material Handler Machine System Specifications Swivel
C4.4 Industrial Engine Compression - Test
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Speed Sensor (Drive Disconnect) (Transmission Output)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Fuse (Flywheel Cabinet)
C6.6 Engines for Caterpillar Built Machines Crankcase Breather
TA22-4WD Agricultural Transmission Transmission
C4.4 Industrial Engine Cleanliness of Fuel System Components
349F and 352F Excavators Machine System Specifications Control Valve (Boom Lowering) - Manual
568 Forest Machine Machine System Specifications Front Idler
2006/07/03 Change to the Design of the Wiring Harness {1408, 7422}
C4.4 Industrial Engine Piston Height - Inspect
2006/08/14 New Procedure for Measuring the Connecting Rod {1218, 1225}
Inspection and Testing of the Air Shutoff{1078} Inspection and Testing of the Air Shutoff{1078}
C9 On-highway Engine Engine to Transmission Adapter
C175-16 Engine for 795F Series AC Off-Highway Trucks Lifter Group
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Keyswitch/EMO Panel
C9 Engines for Caterpillar Built Machines Engine Design
390F Excavator Machine Systems Travel Motor - Assemble
3500B Industrial Engine Refill Capacities and Recommendations