Travel Motor - Assemble
组装步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
D     | 1P-1864     | 钳     | 1     |
E     | 1P-1858     | 钳     | 1     |
F     | 1P-0520     | 起子总成     | 1     |
注: 清洁度是一项重要的因素。 组装之前,应使用清洗剂彻底清洁所有零件。 让零件风干。 不要使用抹布擦干零部件。 棉绒可能会留在零件上,从而在将来引发故障。 检查所有零件。 如果任何零件磨损或损坏,则应使用新零件进行更换。
注: 组装前,将薄薄的一层 10W 机油涂抹到所有部件上。
- 使用工具 (F) 将唇形密封 (51) 安装到行驶马达壳体中。
Show/hide table
图 1 | g01283253 |
- 安装轴承 (50) 和挡圈 (49) 。
Show/hide table
图 2 | g01283244 |
- 加热轴承 (47) 。 将轴承 (47) 安装到轴 (38) 上。
Show/hide table
图 3 | g01283329 |
- 使用工具 (E) ,将挡圈 (48) 安装到轴承 (47) 上。
Show/hide table
图 4 | g01283212 |
- 将轴 (38) 和轴承 (47) 安装到马达壳体中。
Show/hide table
图 5 | g01283209 |
- 使用工具 (D) ,将挡圈 (46) 安装到轴 (38) 上。
Show/hide table
图 6 | g01283206 |
- 安装活塞 (44) 和枢轴 (45) 。
Show/hide table
图 7 | g01283195 |
- 安装旋转斜盘 (43) 。
Show/hide table
图 8 | g01283187 |
- 安装弹簧 (42) 。
Show/hide table
图 9 | g01283193 |
Show/hide table
图 10 | g01283175 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 安装导向器 (41) 。
- 在油缸筒组件 (37) 上安装护圈 (40) 和活塞组件 (39) 。 这些部件必须安装回原来的位置。
Show/hide table
图 11 | g01283155 |
- 将行驶马达放到一旁。
Show/hide table
图 12 | g01283139 |
注: 油缸筒组件 (37) 、活塞组件 (39) 和护圈 (40) 必须在安装到轴 (38) 上时保持完好无损。
- 小心地将油缸筒组件 (37) 安装到轴 (38) 上。
Show/hide table
图 13 | g01283138 |
- 在行驶马达上安装隔板 (35) 和摩擦盘 (36) 。
Show/hide table
图 14 | g01283133 |
- 在行驶马达上安装 O 形密封圈 (33) 和 (34) 。
Show/hide table
图 15 | g01283129 |
- 安装活塞 (32) 。
Show/hide table
图 16 | g01283110 |
注: 活塞 (32) 必须安装回原来的位置。
- 将弹簧 (30) 和 O 形密封圈 (31) 安装到行驶马达上。
Show/hide table
图 17 | g01283350 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
注: 记下弹簧 (30) 的位置以便于安装。
- 冷却轴承 (28) 。 将轴承 (28) 安装到头中。
Show/hide table
图 18 | g01283096 |
- 在减压阀 (24) 上安装 O 形密封圈 (25) 、 (26) 和 (27) 。
Show/hide table
图 19 | g01283088 |
- 安装减压阀 (24) 。 拧紧减压阀 (24) 至扭矩为 44 ± 4 N·m (33 ± 3 lb ft)。
Show/hide table
图 20 | g01283083 |
- 安装盖 (23) 。
- 将 O 形密封圈 (22) 安装到螺塞 (17) 上。 将滑阀 (21) 和螺塞 (17) 安装到头上。
Show/hide table
图 21 | g01283075 |
- 将 O 形密封圈 (19) 安装到螺塞 (18) 上。 将弹簧 (20) 和螺塞 (18) 安装到头上。
- 将螺塞 (17) 和 (18) 拧紧至扭矩为 74 ± 7 N·m (55 ± 5 lb ft)。
- 安装滑阀 (16) 。
Show/hide table
图 22 | g01283060 |
- 安装塞堵 (15) 。
Show/hide table
图 23 | g01283057 |
- 安装 O 形密封圈 (10) 、 (12) 和 (14) 以及备用环 (11) 和 (13) 。
Show/hide table
图 24 | g01283049 |
Show/hide table
弹簧压缩零件如果安装不当,会伤害人体。 为避免伤害,遵照出版的装配程序,并穿上保护装备。 |
- 在阀体 (9) 中安装活塞 (5) 、弹簧 (6) 、滑阀 (7) 和弹簧 (8) 。 将盖 (4) 安装到阀体 (9) 中。
- 重复步骤 27 和 28 以组装其他安全阀。
- 安装安全阀 (3) 。 拧紧安全阀 (3) 至扭矩为 177 ± 18 N·m (131 ± 13 lb ft)。
Show/hide table
图 25 | g01283045 |
- 使用薄润滑脂将孔板 (29) 安装到头上。
Show/hide table
图 26 | g01283396 |
- 将工具 (A) 和适当的起吊设备安装到头 (1) 上。
Show/hide table
图 27 | g01283040 |
- 将头 (1) 定位到行驶马达上。 头 (1) 的重量约为 68 kg (150 lb)。
- 安装内六角头螺栓 (2) 。 拧紧内六角头螺栓 (2) 至扭矩为 235 ± 24 N·m (173 ± 17 lb ft)。
Show/hide table
图 28 | g01282832 |
Show/hide table
注意 |
---|
为了避免系统受到损坏,起动前请确保液压马达中加注了适量的液压油。 |
End By: 安装行驶马达。 请参阅 拆解和组装, "行驶马达 - 安装"。
Caterpillar Information System:
C9 Engines for Caterpillar Built Machines Engine Design
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Keyswitch/EMO Panel
C175-16 Engine for 795F Series AC Off-Highway Trucks Lifter Group
C9 On-highway Engine Engine to Transmission Adapter
Inspection and Testing of the Air Shutoff{1078} Inspection and Testing of the Air Shutoff{1078}
2006/08/14 New Procedure for Measuring the Connecting Rod {1218, 1225}
C4.4 Industrial Engine Piston Height - Inspect
2006/07/03 Change to the Design of the Wiring Harness {1408, 7422}
568 Forest Machine Machine System Specifications Front Idler
349F and 352F Excavators Machine System Specifications Control Valve (Boom Lowering) - Manual
3606 and 3608 Engines Engine Lifting Bracket - Remove and Install
C6.6 Engines for Caterpillar Built Machines Fuel Priming Pump
3500B Industrial Engine Refill Capacities and Recommendations
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys APS Controller PWA
3606 and 3608 Engines Engine Support - Remove and Install
C9 On-highway Engine Exhaust Combustion Group - Aftertreatment Regeneration Device
C6.6 Engines for Caterpillar Built Machines Engine Valve Lash - Inspect/Adjust
C280-12 and C280–16 Marine Engines Mounting Isolator - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys DC Disconnect Switch Handle
2006/11/27 The 285-0910 Multi-Tool Gp Incorporates Four Diagnostic Tools into a Single, Hand Held Unit {0774, 0779, 0781, 0782}
C175-16 and C175-20 Generator Set Engines Fan Drive
2006/06/26 Calibration of the ECPC Valves on Well Servicing OEM Transmissions {3073, 3139, 3167, 4800, 4808, 7000}
3612 and 3616 Engines Air Lubricator - Remove and Install
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys DC Disconnect Indicator