Travel Motor - Disassemble
拆解步骤
Show/hide table
所需工具     | |||
---|---|---|---|
工具     | 零件号     | 零件说明     | 数量     |
A     | 138-7575     | 连杆支架     | 2     |
B     | 1P-0074     | 滑锤拉拔器总成     | 1     |
C     | 123-4370     | 螺杆 M20 x 2.5     | 2     |
D     | 1P-1864     | 钳     | 1     |
E     | 1P-1858     | 钳     | 1     |
F     | 1P-0520     | 起子总成     | 1     |
G     | 8T-0349     | 螺栓     | 2     |
开始:
- 拆下行驶马达。 请参阅拆解和组装, "行驶马达 - 拆卸"。
Show/hide table
注意 |
---|
在检验、保养、测试、调整及维修发动机时,请小心确保盛接流出的液体。 在打开或拆解任何储有液体的部件之前,要准备好合适的容器收集液体。 有关适合收集和盛接卡特彼勒产品上的液体的工具和供应品,请参阅专门出版物, NENG2500, "卡特彼勒代理商工具目录"。 按照本地法规和条例处置所有液体。 |
注: 清洁度是一项重要的因素。 拆解步骤开始之前,应彻底清洁部件外部。 这有助于防止尘土进入内部结构。 污染物或污垢可能会损坏精密部件。 拆解步骤应在清洁的工作面上进行。 务必盖上部件并采取适当保护措施。
- 为便于组装,在行驶马达的所有壳体上标出对准记号。
- 从头 (1) 上拆下呈 180 度的两个内六角头螺栓 (2) 。 使用工具 (G) 更换这两个螺栓。 当拆下其余的内六角头螺栓 (2) 后,工具 (G) 将固定制动器盖。
Show/hide table
图 1 | g01282832 |
Show/hide table
弹簧加压的零件和/或盖板可能导致人身伤害。 拆卸盖板时弹簧力将被释放。 松动螺栓时做好准备把持住弹簧加载的盖板。 |
- 小心拆下固定头 (1) 的其余内六角头螺栓 (2) 。 以交叉顺序均匀拆下内六角头螺栓 (2) 。
- 从头 (1) 上拆下工具 (G) 。
- 将工具 (A) 和适当的起吊设备安装到头 (1) 上。
Show/hide table
图 2 | g01283040 |
- 从行驶马达上拆下头 (1) 。 头 (1) 的重量约为 68 kg (150 lb)。
- 拆下安全阀 (3) 。
Show/hide table
图 3 | g01283045 |
- 从阀体 (9) 拆下盖 (4) 。 从阀体 (9) 上拆下活塞 (5) 、弹簧 (6) 、滑阀 (7) 和弹簧 (8) 。
Show/hide table
图 4 | g01283049 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 拆下 O 形密封圈 (10) 、 (12) 和 (14) 。 拆下备用环 (11) 和 (13) 。
- 从头的另一侧拆下其他安全阀。
- 重复步骤 8 和 9 以拆解其他安全阀。
- 拆下螺塞 (15) 。
Show/hide table
图 5 | g01283057 |
- 拆下滑阀 (16) 。
Show/hide table
图 6 | g01283060 |
- (拆下螺塞) 17。
Show/hide table
图 7 | g01283070 |
Show/hide table
被弹簧力爆出的零件击中,会招致人员伤害。 确保穿上所有必要的保护装备。 遵照建议的程序,并使用所有建议的工具以释放弹簧力。 |
- 从头上拆下滑阀 (21) 。 从螺塞 (17) 上拆下 O 形密封圈 (22) 。
Show/hide table
图 8 | g01283075 |
- 从头的另一侧拆下螺塞 (18) 。 拆下弹簧 (20) 。 从螺塞 (18) 上拆下 O 形密封圈 (19) 。
- 拆下盖 (23) 和减压阀 (24) 。
Show/hide table
图 9 | g01283083 |
- 从减压阀 (24) 上拆下 O 形密封圈 (25) 、 (26) 和 (27) 。
Show/hide table
图 10 | g01283088 |
- 使用工具 (B) 从头上拆下轴承 (28) 。
Show/hide table
图 11 | g01283096 |
- 从行驶马达上拆下孔板 (29) 。
注: 拆卸前记下弹簧 (30) 的位置。
Show/hide table
图 12 | g01283101 |
- 从行驶马达上拆下弹簧 (30) 。
- 拆下 O 形密封圈 (31) 。
- 在活塞 (32) 和壳体上做出对准记号。 活塞 (32) 中的销钉孔必须安装回原来的位置。
Show/hide table
图 13 | g01283110 |
- 将工具 (C) 安装到活塞 (32) 的螺纹孔中。 将工具 (A) 和适当的起吊设备安装在工具 (C) 上,如图所示。 从行驶马达上拆下活塞 (32) 。
Show/hide table
图 14 | g01283120 |
- 从行驶马达上拆下 O 形密封圈 (33) 和 (34) 。
Show/hide table
图 15 | g01283129 |
- 从行驶马达上拆下隔板 (35) 和摩擦盘 (36) 。
Show/hide table
图 16 | g01283133 |
- 将行驶马达放到一旁。 小心地从轴 (38) 上拆下油缸筒组件 (37) 。
Show/hide table
图 17 | g01283138 |
Show/hide table
图 18 | g01283139 |
注: 油缸筒组件 (37) 、活塞组件 (39) 和护圈 (40) 必须在拆卸时保持完好无损。
- 在活塞组件 (39) ,护圈 (40) 和油缸筒组件 (37) 上做出识别标记。 这些部件必须安装回原来的位置。
Show/hide table
图 19 | g01283155 |
- 从油缸筒组件 (37) 上拆下护圈 (40) 和活塞组件 (39) 。
- 拆下导向器 (41) 。
Show/hide table
图 20 | g01283175 |
Show/hide table
图 21 | g01283193 |
- 拆下弹簧 (42) 。
- 逆时针转动旋转斜盘 (43) ,以便在拆卸旋转斜盘 (43) 时提供间隙。
Show/hide table
图 22 | g01283187 |
- 从行驶马达壳体拆下旋转斜盘 (43) 。
- 拆下活塞 (44) 和枢轴 (45) 。
Show/hide table
图 23 | g01283195 |
- 利用工具 (D) 从轴 (38) 上拆下挡圈 (46) 。
Show/hide table
图 24 | g01283206 |
- 利用软面锤从马达壳体上拆下轴 (38) 和轴承 (47) 。
Show/hide table
图 25 | g01283209 |
- 使用工具 (E) 从轴承 (47) 上拆下挡圈 (48) 。
Show/hide table
图 26 | g01283212 |
- 使用适当的压具,从轴 (38) 上拆下轴承 (47) 。
Show/hide table
图 27 | g01283232 |
- 拆下挡圈 (49) 和轴承 (50) 。
Show/hide table
图 28 | g01283244 |
- 使用工具 (F) 从行驶马达壳体上拆下唇形密封 (51) 。
Show/hide table
图 29 | g01283253 |
Caterpillar Information System:
C175-16 Locomotive Engine Engine Speed Sensor
2006/07/03 A New Speed-Timing Sensor is Available {1912}
325D and 329D Excavators and 325D Material Handler Machine System Specifications Swivel
C4.4 Industrial Engine Compression - Test
TH31-C9I, TH31-C9P, TH31-C9T, TH35-C13I, TH35-C13T, TH35-C15I and TH35-C15T Petroleum Power Train Packages and TH31-E61 and TH35-E81 Petroleum Transmissions Transmission Speed Sensor (Drive Disconnect) (Transmission Output)
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Fuse (Flywheel Cabinet)
C6.6 Engines for Caterpillar Built Machines Crankcase Breather
TA22-4WD Agricultural Transmission Transmission
C4.4 Industrial Engine Cleanliness of Fuel System Components
3500B Industrial Engine Safety Messages
C175-16 and C175-20 Generator Set Engines Alternator and Regulator
C13, C15, and C18 Tier 4 Final Engines Connecting Rod
C32 Power Module Engine Valve Lash - Inspect/Adjust
C6.6 Engines for Caterpillar Built Machines Fuel Priming Pump
3606 and 3608 Engines Engine Lifting Bracket - Remove and Install
349F and 352F Excavators Machine System Specifications Control Valve (Boom Lowering) - Manual
568 Forest Machine Machine System Specifications Front Idler
2006/07/03 Change to the Design of the Wiring Harness {1408, 7422}
C4.4 Industrial Engine Piston Height - Inspect
2006/08/14 New Procedure for Measuring the Connecting Rod {1218, 1225}
Inspection and Testing of the Air Shutoff{1078} Inspection and Testing of the Air Shutoff{1078}
C9 On-highway Engine Engine to Transmission Adapter
C175-16 Engine for 795F Series AC Off-Highway Trucks Lifter Group
UPS 1000S/ UPS 1200S Uninterruptible Power Supplys Keyswitch/EMO Panel