Exhaust Manifold - Remove and Install
拆卸步骤
开始:
- 拆下涡轮增压器。 请参阅拆解和组装, "涡轮增压器 - 拆卸"。
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 拆下螺栓 (1) 、垫圈和隔套 (2) 。
Show/hide table
图 1 | g01256526 |
典型示例 |
- 将排气歧管组件和垫片从缸盖组件上拆下。
- 将排气歧管组件拆解为 (3) 、 (4) 和 (5) 三件。
安装步骤
Show/hide table
所需工具     | |||
工具     | 零件号     | 零件描述     | 数量     |
A     | 5P-3931     | 防粘结剂     | -     |
B     | 2P-2333     | 高温密封胶     | -     |
Show/hide table
注意 |
---|
保持所有零件清洁无杂质。 杂质会造成快速磨损和缩短部件寿命。 |
- 在将 (3) 、 (4) 和 (5) 三件组装为排气歧管组件时涂抹工具 (B) 。
注: 清除组装接头上多余的密封胶。
Show/hide table
图 2 | g01256526 |
典型示例 |
- 将工具 (A) 涂抹到螺栓 (1) 上。
- 安装新密封垫,锁键朝上。 将垫片和排气歧管组件定位到缸盖组件上。 安装隔套 (2) 、垫圈和螺栓 (1) 。
- 必要时,更换螺柱 (6) 。 将螺柱 (6) 上紧到 35 ± 5 N·m (26 ± 4 lb ft) 的扭矩。
Show/hide table
图 3 | g01261854 |
- 按照以下步骤拧紧螺栓。
- 按照数字顺序将螺栓 (1) 到螺栓 (12) 依次上紧到 4 ± 1 N·m (35 ± 9 lb in) 的扭矩。
- 按照数字顺序将螺栓 (1) 到螺栓 (12) 依次上紧到 45 ± 5 N·m (33 ± 4 lb ft) 的扭矩。
End By: 安装涡轮增压器。 请参阅 拆解和组装, "涡轮增压器 - 安装"。
Caterpillar Information System:
C3.3 Industrial Engine Crankshaft Rear Seal - Install
C3.3 Industrial Engine Crankshaft Rear Seal - Remove
G3500 A3 Engines Engine Overload
G3500 A3 Engines Engine Overcrank
C9 Industrial Engines Coolant Temperature Sensor
C7 PETROLEUM Petroleum Engine Turbocharger - Install
3500B and 3500C Locomotive Engines Air Shutoff System
C7 PETROLEUM Petroleum Engine Turbocharger - Remove
C15 Industrial Engine Idle Shutdown Timer - Test
C3.3 and C4.4 Generator Sets Valve Mechanism Cover - Remove and Install - Four Cylinder Engines
G3500 Engines After Starting Engine
C3.3 and C4.4 Generator Sets Crankcase Breather - Remove and Install
C7 On-Highway Engine Clean Gas Induction Cooler - Remove and Install
G3508, G3512 and G3516 Engines Crankshaft - Remove
C280 Marine Auxiliary Engines Self-Diagnostics
C280 Marine Propulsion Engines Intermittent Engine Shutdown
Air Conditioning and Heating R134a for All Caterpillar Machines Identifying the Air Conditioning System
C7 PETROLEUM Petroleum Engine Inlet and Exhaust Valve Springs - Remove and Install
C13 and C15 On-Highway Engines Emissions Certification Film
C7 PETROLEUM Petroleum Engine Inlet and Exhaust Valves - Remove and Install
G3508, G3512 and G3516 Engines Crankshaft - Install
AccuGrade® GPS (CD700) Flashing Messages
C7 On-highway Engine Idler Pulley
AccuGrade® GPS (CD700) Radio Utility