Pump Drive - Install
Installation Procedure
Show/hide table
| Required Tools | |||
|---|---|---|---|
| Tool | Part Number | Part Description | Qty |
| A | 138-7573 | Link Bracket | 1 |
| B | 174-8987 | Left Engine Bracket | 1 |
| C | 174-8989 | Right Engine Bracket | 1 |
- Attach a hoist to the pump drive by using Tooling (A), as shown. Move the pump drive into position.
Show/hide table
 | |
| Illustration 1 | g00578388 |
- Install pump drive (20). Install twelve bolts (19) that connect pump drive (20) to flexible coupling (21).
Show/hide table
 | |
| Illustration 2 | g00578438 |
- Install six bolts (18) into the left side of the pump drive.
Show/hide table
 | |
| Illustration 3 | g00578437 |
- Install six bolts (17) into the right side of the pump drive.
Show/hide table
 | |
| Illustration 4 | g00578433 |
- Remove Tooling (B) from the right side of the engine block. Remove Tooling (C) from the left side of the engine block. Remove Tooling (A) and the hoist.
Show/hide table
 | |
| Illustration 5 | g00578391 |
Tooling (C) | |
- Install spacer (16) and bolt (15) .
Show/hide table
 | |
| Illustration 6 | g00571378 |
- Install bolt (12) and the washer. Install ground cable (14) and nut (13).
Show/hide table
 | |
| Illustration 7 | g00571319 |
- Install four bolts (10), the washers and the tube. Install tube (5), the four mounting bolts and the washers. Tighten fitting (11) .
Show/hide table
 | |
| Illustration 8 | g00571130 |
- Put tube (4) and the two lines groups into position. Install bolts (6), (7), (8) and (9). Tighten fitting on tube (4) .
Show/hide table
 | |
| Illustration 9 | g00571123 |
- Tighten the fittings on tubes (2), (3), (4) and (5) .
Show/hide table
 | |
| Illustration 10 | g00571067 |
- Fill the pump drive with 3.8 L (1.00 US gal) of 10W hydraulic oil. Refer to Operation and Maintenance Manual, SEBU7098 for additional information.
End By:
- Install the equipment pump. Refer to Disassembly and Assembly, "Equipment Pump - Install" for the machine that is being serviced.
- Install the drive pumps. Refer to Disassembly and Assembly, "Hydraulic Drive Pump - Install" for the machine that is being serviced.
- Install the cab. Refer to Disassembly and AssemblySENR1831, "Cab - Install" for the machine that is being serviced.
Caterpillar Information System:
3003, 3013, 3014 and 3024 Engines for Caterpillar Built Machines Flywheel - Remove
854G Wheel Dozer Seat
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Remove
611 Wheel Tractor-Scraper Wheel Tractor-Scraper Power Train Wheel Bearings - Adjust
994D Wheel Loader Power Train Auxiliary Drive Shaft - Install
D11R Track-Type Tractor Refrigerant Dryer - Replace
D11R Track-Type Tractor Air Conditioner In-Line Dryer - Inspect
D8R Track-Type Tractor Air Conditioner In-Line Dryer - Replace
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Transfer Pump
3176C and 3196 Engines for Caterpillar Built Machines Inlet Manifold Pressure - Test
994D Wheel Loader Power Train Auxiliary Drive Shaft - Remove
994D Wheel Loader Engine Supplement Fuel Transfer Pump - Remove and Install
3034 Engine for Caterpillar Built Machines Exhaust Manifold - Remove and Install
D10R Track-Type Tractor Indicators and Gauges - Test
3408E and 3412E Engines for Caterpillar Built Machines Flywheel - Install
D11R Track-Type Tractor Indicators and Gauges - Test
D10R Track-Type Tractor Fuses and Circuit Breakers - Replace/Reset
613C Series II Wheel Tractor-Scraper Changing Direction and Speed
D6R Series II Track-Type Tractor Hydraulic System Hydraulic Pump - Piston
D11R Track-Type Tractor Fuses and Circuit Breaker - Replace/Reset
D7R Series II Track-Type Tractor Hydraulic System Ripper Tip Control Valve
3114, 3116 and 3126 Industrial, Marine and Generator Set Engines Fuel Filter Lines
D7R Series II Track-Type Tractor Power Train References
613C Series II Wheel Tractor-Scraper Braking Operation