Wire Harness May Contact The Muffler Support Caterpillar

Wire Harness May Contact The Muffler Support

Usage:

TRACK-TYPE TRACTORS

TRACK-TYPE LOADERS

D3C Series III (4KS, 4TS, 5GS, 6SL, 7XL, 9TS, D4C Series III (4LS, 6BS, 8CS, 1FW, 6YL, 7SL),
D5C Series III (5HS, 6CS, 7PS, 6ZL, 8ZS, 9DL) TRACK-TYPE TRACTORS;
933 (8FL, 9EL),
933C (5JS, 4MS),
939 (9GL),
939C (6DS) TRACK-TYPE LOADERS

Problem:

The wire harness may contact the muffler support. Symptoms of this problem are:

The hour meter may stop registering.

Alternator failure. If the alternator fails, the voltage regulator shorts.

Solution:

Remove the tie strap at the muffler support. Check the wire harness for any wear and repair if necessary. See Chart 1 for the parts required.

Installation Procedure

1. Drill the existing hole (A) to 9 mm (.355 in) diameter.

2. Install the 4P-8134 Clip (1) to the muffler support using a 8T-4189 Bolt (2), 8T-4224 Washer (3), and 5C-7261 Nut(4). See illustration 1.

3. Install a 3S-2093 Tie Strap (5) to the 4P-8134 Clip (1) and the Wire Harness.

Illustration 1.

Muffler Bracket drill a Point (A).

Install Clip (1)

Bolt (2)

Washer (3)

and Nut (4).

Caterpillar Information System:

Open Rops Heater Relay Open Rops Heater Relay

Air Conditioner Leaking Condensation Into Cab Air Conditioner Leaking Condensation Into Cab

Aftercooler Coolant Hose Clamps May Be Incorrectly Tightened Aftercooler Coolant Hose Clamps May Be Incorrectly Tightened

High Brass Readings In Power Train Oil System High Brass Readings In Power Train Oil System

Inspect Sprocket Segment Mounting Bolts Inspect Sprocket Segment Mounting Bolts

Early Hour Clutch Plate And Piston Tang Wear Is Normal Early Hour Clutch Plate And Piston Tang Wear Is Normal

Loss Of Logs From Grapple When Operating Boom Or Arch Functions At Low Engine Speeds Loss Of Logs From Grapple When Operating Boom Or Arch Functions At Low Engine Speeds

Cab Air Filter Cab Air Filter

Computerized Monitoring System Computerized Monitoring System

Structural Paint On Lift Arms Structural Paint On Lift Arms

Brake Oil Cooler Guide Brake Oil Cooler Guide

Clutch Failures And Inadequate Lubrication Of Planetary Group Parts Clutch Failures And Inadequate Lubrication Of Planetary Group Parts

Cracks May Occur In Push Arm Bearing Assembly Welds Cracks May Occur In Push Arm Bearing Assembly Welds

Final Drive Planet Bearings Final Drive Planet Bearings

Correct Machining Of The 130-9004 Intake Valve Seat Insert Correct Machining Of The 130-9004 Intake Valve Seat Insert

Damage To Hydraulic Hoses On Lift Circuit Damage To Hydraulic Hoses On Lift Circuit

Camshaft Injector Lifter (Roller Follower) Assembly Replacement Camshaft Injector Lifter (Roller Follower) Assembly Replacement

Removing Invalid Service Codes (MID 030, CID 511, FMI 55) Removing Invalid Service Codes (MID 030, CID 511, FMI 55)

Procedures To Resolve Certain Causes Of Low Drivetrain Power Procedures To Resolve Certain Causes Of Low Drivetrain Power

Air Conditioning Unit May Fall Off The Back Of The Cab On Some 953C Machines Air Conditioning Unit May Fall Off The Back Of The Cab On Some 953C Machines

New Hydraulic Electronic Control Improves Blade Control New Hydraulic Electronic Control Improves Blade Control

Noise In Differential Or Copper In Power-Train Oil Noise In Differential Or Copper In Power-Train Oil

Front Guard Changed To Prevent Interference With Tilt Cylinder Front Guard Changed To Prevent Interference With Tilt Cylinder

Engine Fan Drive Group Engine Fan Drive Group