5P1075 And 5P1076 Washers Have A Different Design{7553,0680}
Usage:
The designs of the 5P1075 and 5P1076 Washers have been changed. These washers are hardened, flat washers.
Formerly the 5P1075 and 5P1076 Washers were of a conical design. The part numbers did not change.
The 5P1075 and 5P1076 Washers have many applications in Caterpillar products. One example is the hood group for the 826C Compactor.
The hardened, flat 5P1075 and 5P1076 Washers can be used in any application where the conical washers were used.
Caterpillar Information System:
1981/03/16 Approximate Liquid (Refill) Capacities Added To Specifications Page In Parts Book{0374}
1981/03/09 Clean Electrical Contacts In Exhaust Gas Recirculation (E.G.R.) Switch Group And Cover Assembly Before Installation{1080}
1981/03/09 New Aftercooler Core has Improved Design To Prevent Vibration Damage Which Lets Coolant Into Engine Air Inlet{1064}
1981/03/09 Correct Installation Of Inserts Necessary During Repairs To Prevent More Counterbore Cracks{1217,1201}
1981/03/09 Special Studs And Nuts Available For Exhaust Manifolds On Engines Used In Heavy Load Conditions{1059,1101}
1981/03/09 Test Procedure For Exciter Reactors On SRSE Generators{4454}
1981/03/09 New Poppet Valves And Piston Available As Replacement Parts; Automatic Center Punch Can Be Used To Install Piston{3012,0622,0626,3166,3185}
1981/03/09 Correct Preparation Is Important To Prevent Damage During Extended Periods Of Storage{7500}
1981/03/02 Check Oil Level Carefully To Prevent Operation With Too Much Oil In Engine Crankcase{1316}
1981/03/02 Modification Of Flywheel Prevents Loose Clutch Pilot Bearing{1155,1156}
1981/03/02 Two New Exhaust Manifolds Available For Replacement Of Single Rear Manifold To Prevent Broken Studs{1059}
1981/03/02 High Concentration Of Aluminum In Oil Analysis Can Be The Result Of Rocker Arm Support Wear{1318,1102}
1981/03/16 New Inlet And Exhaust Valves And Valve Guides Have Tighter Fit To Prevent Corrosion And Guide Wear{1104,1105,1101,1103,1108,1109}
1981/03/16 New Shield Assemblies Used In Water Shielded Manifold Group{1067}
1981/03/23 6V2029 Fixture Group Available For Adjustment Of Air/Fuel Ratio Control {0626,1278,0652}
1981/03/23 6V4009 Dowel Driver Available {0622,1101}
1981/03/23 Fuel Pressure Relief Valve Is Shown Inverted (Wrong End Up) In Parts Book Illustrations {1253,1286}
1981/03/23 Longer Cable Assembly Now Used In The 9S2000 Flowmeter {0651}
1981/03/23 Correction To Torque Specification For Locknuts On Valve Clearance Adjustment Screws Of Engines Equipped With Jacobs Engine Brakes {1119,1102}
1981/03/23 New Tool Makes Glow Plug Wire Removal Easier {0622,0621,1403}
1981/03/30 Check All Settings When Fuel Injection Pump Group Is Installed{1286,1264,1251,1253}
1981/03/30 Low Engine Temperatures: Install Check Valve{1353,1355,1370,1380}
1981/03/30 6V3197 Spacer, 6V3041 Tool Group Available For Use During Removal and Installation Of Piston Pin Bearings{0622,1219,1218,1214}
1981/03/30 6V3150 Engine Pressure Group Gives Direct Indication Of Manifold Pressure{0651,1058}