Emergency Stopping
Show/hide table
注意 |
---|
紧急停机控制装置只用于紧急情况。 切勿把紧急停机装置或控制装置用于正常的停机过程。 |
在发动机停机之后,确保为发动机运行提供外部支持的所有系统是安全可靠的。 发动机停止后关掉发动机运行的辅助系统。
Show/hide table
注意 |
---|
在找到迫使发动机紧急停机的问题并予以纠正以前,不要起动发动机。 |
按紧急停机按钮可能造成未燃烧气体残留在空气进气管和排气歧管里。
Show/hide table
当发动机被起动时,进排气系统里残存的燃气可能被点燃。 可能造成人身伤害和/或财产损失。 起动一台含未燃烧的燃气的发动机之前,从进排气系统清除这些未燃烧的燃气。 参阅"起动发动机"有关清除未燃烧燃气的章节。 |
Show/hide table
图 1 | g00792865 |
(1) 紧急停机按钮
(2) 模式控制开关在"断开(OFF)/复位(RESET)"位置 |
在发动机正常运转时的紧急停机按钮是在伸出(OUT)位置。 要紧急停机,按紧急停机按钮 (2)。 该按钮被锁定时,发动机将不能起动。 为复位按钮,顺时针转动按钮或拉按钮。 弹簧加载的按钮会回到伸出(OUT)位置。
控制仪表板在发动机起动前必须复位。 将模式控制开关 (1)转到"断开/复位(OFF/RESET)"位置来复位控制仪表板。
另一个紧急停机按钮位于发动机后部 ECM 接线盒上。
Caterpillar Information System:
3412C Engine Flywheel - Install
3606, 3608, 3612, 3616 and 3618 Engines Tachometer General Information
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Sensors
3034 Marine Engine Model View Illustrations
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Potentiometers
3406E Generator Set Engines Starting the Engine
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Indicators
Electronic Modular Control Panel II+ (EMCP II+) EMCP Electronic Control (Generator Set)
Air Conditioning and Heating R134a for All Caterpillar Machines Electronic Heat Control - Test
Product Identification Numbers (PIN) Location Guide Ripper
Product Identification Numbers (PIN) Location Guide Bulldozer
Electronic Modular Control Panel II+ (EMCP II+) Data Link
Electronic Modular Control Panel II+ (EMCP II+) Service Mode
3412C Engine Flywheel - Remove
3034 Marine Engine Alternator Belt - Inspect/Adjust/Replace
Electronic Modular Control Panel II+ (EMCP II+) Modes Of Operation
3412C Engine Cylinder Head - Install
Electronic Modular Control Panel II+ (EMCP II+) Engine/Generator Programming OP5-0
Electronic Modular Control Panel II+ (EMCP II+) Normal Mode
3034 Marine Engine Cooling System Coolant (DEAC) - Change
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Speed Sensor - Adjust
3606, 3608, 3612 and 3616 Engines and C280-12, C280-16, C280-6 and C280-8 Marine Engines Control Panel Component Location
2001/05/01 New Valve Guides Are Used {1104}
Electronic Modular Control Panel II+ (EMCP II+) Protective Relaying Programming OP5-1