Piston Motor - Remove
Removal Procedure
Show/hide table
| Required Tools | |||
| Tool | Pt. No. | Description | Qty |
| A | 4C-6486 | Stand | 4 |
| 8S-7641 | Tube | 2 | |
| 8S-7621 | Tube | 2 | |
| 8S-7625 | Collar | 1 | |
| 8S-8048 | Saddle | 4 | |
| 8S-7615 | Pin | 4 | |
| 189-0411 | Shackle As | 1 | |
| - | Pipe (51 mm (2 inch) OD) | 1 | |
| B | 138-7575 | Link Bracket | 2 |
| C | 169-6969 | Threaded Stud (M16 X 2 X 400 mm) | 1 |
Show/hide table
| NOTICE |
|---|
Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. |
Show/hide table
| NOTICE |
|---|
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop Products Guide" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. |
- Use Tooling (A) to support the work tool.
Show/hide table
 | |
| Illustration 1 | g01013336 |
Show/hide table
 | |
| Illustration 2 | g01013350 |
- Remove nuts (1) .
Show/hide table
 | |
| Illustration 3 | g01013643 |
- Remove hose assemblies (4). Remove bolts (3) and (5) .
Show/hide table
 | |
| Illustration 4 | g01013644 |
- Loosen each bolt (2) by five turns. Slide piston motor (6) against bolts (2) .
- Install Tooling (B) and (C). Attach a suitable lifting device to piston motor (6). The piston motor weighs approximately 91 kg (200 lb).
Show/hide table
 | |
| Illustration 5 | g01013649 |
- Remove bolts (2). Remove piston motor (6) .
Caterpillar Information System:
2003/08/18 New Software is Available for the M300C Wheeled Excavators {7601, 7620}
Standalone Installation of the Machine Security System (MSS) Medium Excavator{7631} Standalone Installation of the Machine Security System (MSS) Medium Excavator{7631}
C11 and C13 Engines for Caterpillar Built Machines Crankshaft - Remove
G310B, G315B and G320B Demolition and Sorting Grapples Hydraulic Cylinder - Remove and Install
SW45 and SW60 Wheel Saws Hydraulic Cylinder (Depth) - Remove and Install
2003/11/24 Remanufactured Improved Travel Motors With Increased Service Life Are Now Available {5058}
321C LCR Excavator Machine Systems Undercarriage Frame - Install
321C LCR Excavator Machine Systems Undercarriage Frame - Remove
2003/08/01 A Previous High Temperature Locknut is Used in Engine Exhaust System Groups {7553}
SW45 and SW60 Wheel Saws Check Valve - Remove and Install
321C LCR Excavator Machine Systems Cab - Install
321C LCR Excavator Machine Systems Cab - Remove
SW45 and SW60 Wheel Saws Piston Motor - Install
2003/08/18 New Software is Available for the M300C Wheeled Excavators {7610, 7620}
2003/09/01 New Engine Software is Available for the M300C Wheeled Excavators {1902, 7620}
315C Excavator Machine Systems Front Idler, Recoil Spring and Hydraulic Track Adjuster - Remove
C15 and C18 Generator Set Engines Cylinder Liner - Install
C15 and C18 Generator Set Engines Cylinder Liner - Remove
SW45 and SW60 Wheel Saws Hydraulic Cylinder (Trench Cleaner) - Remove and Install
322C Excavator Daily Inspection
330C Excavator Daily Inspection
330B L Excavator, 330B Forest Machine and 330B Material Handler Daily Inspection
320C Excavator Operation
321C LCR Excavator Machine Systems Control Manifold (Pilot Oil) - Remove