Reverse Switch - Test
Show/hide table
Engine exhaust contains products of combustion which may be harmful to your health. Always start and operate the engine in a well ventilated area and, if in an enclosed area, vent the exhaust to the outside. |
Show/hide table
Machine Test Parameters | ||
---|---|---|
Date | Product or Component SN | |
Measurement Location | Measurement | Actual |
Hydraulic oil temperature for test | |
Show/hide table
Reverse Switch Specifications | ||
---|---|---|
Date | Product or Component SN | |
Condition | Status | Actual |
Switch state with propel lever in the forward position or in the neutral position | Open | |
Switch state with propel lever in the reverse position | Closed |
Note: If the machine moves in reverse before the back-up alarm begins to operate, replace the propel handle.
This procedure confirms that the reverse switch is operating properly. Perform this test under any of the following conditions:
- The back-up alarm does not operate.
- The back-up alarm continuously operates.
Show/hide table
Required Tools | ||||
---|---|---|---|---|
Tool | Item | Qty | Part No | Description |
A | 1 | 146-4080 | Digital Multimeter Gp | |
B | 1 | 7X-1710 | Multimeter Probe |
- Drive the machine to a smooth, horizontal surface.
Show/hide table
Illustration 1 g06182706 - Move propel lever (1) to the NEUTRAL position.
Show/hide table
Illustration 2 g06182711 - Move parking brake switch (2) to the ON position.
Show/hide table
Illustration 3 g06182714 - Move throttle lever (3) to the LOW-IDLE position.
Show/hide table
Illustration 4 g06182717 - Move engine start switch (4) to the OFF position.
- Remove six screws (5), and tilt plate (6) forward.
Show/hide table
Illustration 5 g06187560 - Remove six screws (5), and tilt plate (6) forward.
Show/hide table
Illustration 6 g06241618 - Insert black spoon from Tool (B) to into pin"3" of connector (7). Insert red spoon from Tool (B) into pin"4" of the connector.
- Connect Tool (B) to Tool (A).
- Make sure propel lever (1) is in the NEUTRAL position.
- Set Tool (A) to measure continuity. The circuit across the switch should be open. If the circuit across the switch is closed, replace the propel lever, and retest the switch. If the circuit across the switch is open, go to the next step.
- Move propel lever (1) into the reverse range. The circuit across the reverse switch should close when the propel lever is moved into the reverse range.
- Move propel lever (1) into the NEUTRAL position. If the switch does not operate as described above, replace the propel handle, and retest the reverse switch. If the switch operates as described above, go to the next step.
- Remove Tool (B) from reverse switch connector (7).
- Plug reverse switch connector (7) into the machine harness.
- Position cover (6), and install six screws (5).
Caterpillar Information System:
3516E Engines for Caterpillar Built Machines Engine Oil Cooler - Remove and Install
CB1.7 Utility Compactor Machine Systems Visual Inspection
CB1.7 Utility Compactor Machine Systems Machine Preparation for Troubleshooting
785G Off-Highway Truck Systems Torque Converter
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Engine Air Precleaner - Inspect/Clean
730 EJ Articulated Truck Ejector Control
422F2, 426F2, 428F2, 432F2, 434F2 and 444F2 Backhoe Loaders Engine Air Filter Element - Clean/Replace
785G Off-Highway Truck Systems Electronic Control (Steering System)
An Improved Assembly Procedure for the Control Group Lever Is Now Used on Certain 424B Backhoe Loaders {5063} An Improved Assembly Procedure for the Control Group Lever Is Now Used on Certain 424B Backhoe Loaders {5063}
785G Off-Highway Truck Systems Magnetic Screen (Torque Converter)
Improved Tilt Cylinder Heads and Tilt Cylinder Head Seals Are Now Used on Certain TL1055D and TL1255D Telehandlers {5104} Improved Tilt Cylinder Heads and Tilt Cylinder Head Seals Are Now Used on Certain TL1055D and TL1255D Telehandlers {5104}
426F2 Backhoe Loader Power Train Axle Housing and Flange - Install
994K Wheel Loader Diesel Exhaust Fluid - Fill - Emission Related Component
745 & 740 GC Articulated Truck Brake Accumulator (Parking) - Test and Charge
Resolving Error Code 874 "Maintenance Interval" on Certain Telehandlers {0374, 1901, 7500, 7620} Resolving Error Code 874 "Maintenance Interval" on Certain Telehandlers {0374, 1901, 7500, 7620}
CB1.7 Utility Compactor Machine Systems Vibratory Frequency - Test
994K Wheel Loader DEF Manifold Filters - Replace - Emission Related Component
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System General Information (Propel System)
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System Operator Controls (Propel System)
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System Location of Electrical Components (Propel System)
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System Location of Hydraulic Components (Propel System)
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System Piston Pump (Propel)
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System Piston Motors (Drum Propel and Wheel Propel)
CB2.5, CB2.7, CB2.9 and CC2.6 Vibratory Utility Compactors Propel System Electrical Schematic (Propel System)