Engine Speed/Timing Sensor - Clean/Inspect
飛輪殼體內裝有一個引擎轉速/正時感測器。 該感測器向 ECM 提供關於引擎轉速和曲軸位置的資訊。
- 拆下引擎轉速/正時感測器 ( 1)。 檢查磁鐵端面的狀態。 檢查磨損和污染物跡象。
- 從磁鐵端面上清除任何碎屑。
Show/hide table
插圖 2 g01115363 - 檢查滑動頭的張力。 輕輕將滑動頭 (2) 拉出最少
4 mm (0.16 inch) 。 然後將滑動頭推回。當滑動頭的張力正確時,將滑動頭從伸出位置推回至少需要
22 N () 的力。Show/hide table注意事項 安裝速度/正時感測器時,滑動頭必須充分伸出,使得感測器保持與轉速-正時齒輪的接觸。 如果不保養正確的間隙,則訊號不會自感測器中產生。
不要在轉速-正時齒輪間安裝感測器。 可能導致感測器的損壞。 安裝感測器前,確認感測器的安裝孔中可見到齒輪的齒。
- 安裝引擎轉速/正時感測器。
- 確保感測器安裝孔中可以看得到一個轉速-正時齒輪的齒。
- 將滑動頭 (2) 拉出最少
4 mm (0.16) 。 - 在感測器的螺紋上塗抹 4C-5597 防咬合膏。
附註滑動頭是設計來在轉速-正時齒輪轉第一圈時接觸齒的。 如需滑動頭和齒之間的最大允許間隙,請參閱引擎的 技術規格手冊。
- 安裝感測器。 將防鬆鎖帽用
40 ± 5 N·m (30 ± 4 lb ft) 的扭矩擰緊。
Show/hide table
插圖 1 | g00760464 |
Caterpillar Information System:
G3612 and G3616 Engines Flexible Coupling
3054B Industrial Engine Electrical System
G3300 Engines Engine Air Cleaner Element - Replace
Procedures For The Installation And Initial Start-Up Of Gas Engine Chiller Drivelines{1014} Procedures For The Installation And Initial Start-Up Of Gas Engine Chiller Drivelines{1014}
Electronic Modular Control Panel II (EMCP II) AL Fault Codes
G3500 Engines Cylinders - Inspect
3508B, 3512B, and 3516B High Displacement Generator Sets Engine Rating Definitions
3618 Engine Prelube Pump Motors
G3500 Engines Engine Oil Filter (Auxiliary) - Change
3508, 3512 and 3516 Engines Ether Control System
3618 Engine Electronic Sensors
Electronic Modular Control Panel II (EMCP II) For MUI Engines AC Offset Adjustment OP10
3208 Marine Engine Engine Operation
3408B and 3412C Generator Set Engines Basic Block
G3500 Engines Speed Sensor - Clean/Inspect
3618 Engine Turbocharger
3306B Industrial Engine Engine Air Cleaner Element (Dual Element) - Clean/Replace
3618 Engine Aftercooler
3408B and 3412C Generator Set Engines Engine Design
G3300 Engines Cold Weather Starting
G3500 Engines Before Starting Engine
3408B and 3412C Generator Set Engines Basic Block
3500B and 3500B High Displacement Generator Set Engines Electronic Control Module (ECM)
345B Excavator Swing Gear - Lubricate