Intake Manifold Air Pressure Is High
The Electronic Control Module (ECM) monitors the intake manifold air pressure. The following event is associated with high intake manifold air pressure:
Show/hide table
Diagnostic Trouble Code for Intake Manifold Air Pressure Is High | |||
---|---|---|---|
J1939 Code | CDL Code | Code Description
(Code descriptions may vary) |
Comments |
102-16 | E1044 (2) | Engine Intake Manifold #1 Pressure : High - moderate severity (2) | This pressure is a variable value that is calculated by the ECM. The resulting value depends on the operating conditions of the engine. |
- Turbocharger wastegate
- Wastegate regulator
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. Turbocharger Wastegate Note: The wastegate is attached to the high-pressure turbocharger. A. Check the operation of the wastegate on the turbocharger. B. Check the operation of the wastegate actuator on the turbocharger. Refer to Systems Operation, Testing, and Adjusting, "Turbocharger - Inspect". |
Turbocharger wastegate |
Result: Operation of the turbocharger wastegate is suspect. Repair: Disconnect the output rod in the wastegate actuator from the lever that operates the wastegate. Operate the wastegate lever by hand and check for full and free movement. Check that the output rod in the wastegate actuator is biased towards the retracted position. Connect the output rod in the wastegate actuator to the lever that operates the wastegate. If the wastegate is not operating correctly, replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install". Result: There is a suspected fault in the wastegate or the wastegate actuator. Repair: Replace the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove" and Disassembly and Assembly, "Turbocharger - Install". Result: The wastegate and the wastegate actuator operate correctly. Proceed to Test Step 2. |
2. Wastegate Regulator A. Use the electronic service tool to check for diagnostic trouble codes that relate to the wastegate regulator. |
Wastegate regulator |
Result: Diagnostic codes are present that relate to the wastegate regulator. Repair: Rectify the cause of any related codes. Refer to Troubleshooting, "Diagnostic Trouble Codes". Result: There are no diagnostic codes that relate to the wastegate regulator. Contact the Dealer Solutions Network (DSN). |
Caterpillar Information System:
980L Tier 3 Wheel Loader Engine Supplement Expansion Tank - Remove and Install
C7.1 Engines and Generator Sets Inlet Air Is Restricted
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Disassemble
C7.1 Engines and Generator Sets Fuel Temperature Is High
C7.1 Engines and Generator Sets Fuel Rail Pressure Problem
2570D and 2670D Wheel Feller Buncher Engine Supplement Piston Motor (Fan) - Remove and Install
C7.1 Engines and Generator Sets Fuel Contains Water
MH3037 Material Handler Machine Systems Main Control Valve - Remove and Install - Lower Valve
C7.1 Engines and Generator Sets Fuel Consumption Is Excessive
Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380} Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380}
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Remove and Install
C7.1 Engines and Generator Sets Exhaust System Contains Oil
C7.1 Engines and Generator Sets Intake Manifold Air Pressure Is Low
C7.1 Engines and Generator Sets Intake Manifold Air Temperature Is High
New Piston and Gear Pump Group Is Now Available for Certain Compact Track Loaders, Multi-Terrain Loaders, and Skid Steer Loaders {5073} New Piston and Gear Pump Group Is Now Available for Certain Compact Track Loaders, Multi-Terrain Loaders, and Skid Steer Loaders {5073}
CB54B Vibratory Asphalt Compactor Machine Systems Articulating Hitch (Offset)
994K Wheel Loader Power Train Pump Drive (Front) - Remove and Install
A New Pad Assembly for the Stabilizer Group Is Now Available on Certain Knuckleboom Loaders {7222} A New Pad Assembly for the Stabilizer Group Is Now Available on Certain Knuckleboom Loaders {7222}
The Orientation of the Rear Suspension Group is Improved on Certain 777 Off-Highway Trucks {0679, 0756, 7200, 7201, 7213} The Orientation of the Rear Suspension Group is Improved on Certain 777 Off-Highway Trucks {0679, 0756, 7200, 7201, 7213}
High Pitch Noise from the Flushing Valve May Occur on Certain Skid Steer Loaders {4351, 5058} High Pitch Noise from the Flushing Valve May Occur on Certain Skid Steer Loaders {4351, 5058}
Installation Procedure of the Gusset Plate in the Frame Assembly on Certain HF201B Felling Heads {6319} Installation Procedure of the Gusset Plate in the Frame Assembly on Certain HF201B Felling Heads {6319}
New Gusset Plate in the Frame Assembly Is Now Used on Certain HF201B Felling Heads {6319} New Gusset Plate in the Frame Assembly Is Now Used on Certain HF201B Felling Heads {6319}
980M Tier 4 and 982M Tier 4 Wheel Loaders Machine Systems Tilt Lever and Tilt Link - Remove and Install
525D, 535D, 545D and 555D Wheel Skidders C7.1 Engine Supplement Piston Motor (Fan) - Disassemble