Inlet Air Is Restricted
Use this procedure to troubleshoot a high differential pressure for the air inlet system. Use this procedure if one of the following event codes are active. Refer to Troubleshooting, "Event Codes" for information about event codes. Access the engine monitoring system on the electronic service tool to view the current trip points for these codes. For information on the engine monitoring system, refer to Troubleshooting, "Engine Monitoring System".
Show/hide table
| Diagnostic Trouble Codes for Inlet Air Is Restricted | |||
|---|---|---|---|
| J1939 Code | CDL Code | Code Description
(Code descriptions may vary) |
Comments |
| 107-15 | E583(1) | Engine Air Filter 1 Differential Pressure : High - least severe (1) | The air filter differential pressure is above the trip point pressure for the delay time.
The code is logged. |
| 107-16 | E583(2) | Engine Air Filter 1 Differential Pressure : High - moderate severity (2) | The air filter differential pressure is above the trip point pressure for the delay time.
The code is logged. The engine power is derated. |
Complete the procedure in the order in which the steps are listed.
Show/hide table
| Troubleshooting Test Steps | Values | Results |
|---|---|---|
1. Check the Air Filter Element A. Check the air intake system for plugged air filters or for damaged air filters. If the engine is equipped with an air intake precleaner, verify the proper operation of the air intake precleaner. |
Plugged air filter |
Result: The air filter is clogged. Repair: Clean or replace the air filter. Verify that the problem is resolved. Result: The air filter is not clogged. Proceed to Test Step 2. |
2. Check the Air Inlet Piping A. Check the air inlet piping for damage or restrictions. |
Damaged air inlet piping |
Result: The air inlet piping is damaged or has restrictions. Repair: Repair the piping or replace the piping. Verify that the problem is resolved. Result: The air inlet piping does not have damage or restrictions. Proceed to Test Step 3. |
3. Check the Enclosure Ventilation A. Check that the engine has been installed in an enclosure that is sufficiently ventilated. |
Enclosure ventilation |
Result: The engine does not have sufficient ventilation. Repair: Repair the ventilation for the enclosure. Verify that the fault is resolved. Result: The engine has sufficient ventilation. Contact the Dealer Solutions Network (DSN). |
Caterpillar Information System:
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Disassemble
C7.1 Engines and Generator Sets Fuel Temperature Is High
C7.1 Engines and Generator Sets Fuel Rail Pressure Problem
2570D and 2670D Wheel Feller Buncher Engine Supplement Piston Motor (Fan) - Remove and Install
C7.1 Engines and Generator Sets Fuel Contains Water
MH3037 Material Handler Machine Systems Main Control Valve - Remove and Install - Lower Valve
C7.1 Engines and Generator Sets Fuel Consumption Is Excessive
Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380} Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380}
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Remove and Install
C7.1 Engines and Generator Sets Exhaust System Contains Oil
980L Tier 3 Wheel Loader Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
C7.1 Engines and Generator Sets Exhaust System Contains Fuel
980L Tier 3 Wheel Loader Engine Supplement Expansion Tank - Remove and Install
C7.1 Engines and Generator Sets Intake Manifold Air Pressure Is High
C7.1 Engines and Generator Sets Intake Manifold Air Pressure Is Low
C7.1 Engines and Generator Sets Intake Manifold Air Temperature Is High
New Piston and Gear Pump Group Is Now Available for Certain Compact Track Loaders, Multi-Terrain Loaders, and Skid Steer Loaders {5073} New Piston and Gear Pump Group Is Now Available for Certain Compact Track Loaders, Multi-Terrain Loaders, and Skid Steer Loaders {5073}
CB54B Vibratory Asphalt Compactor Machine Systems Articulating Hitch (Offset)
994K Wheel Loader Power Train Pump Drive (Front) - Remove and Install
A New Pad Assembly for the Stabilizer Group Is Now Available on Certain Knuckleboom Loaders {7222} A New Pad Assembly for the Stabilizer Group Is Now Available on Certain Knuckleboom Loaders {7222}
The Orientation of the Rear Suspension Group is Improved on Certain 777 Off-Highway Trucks {0679, 0756, 7200, 7201, 7213} The Orientation of the Rear Suspension Group is Improved on Certain 777 Off-Highway Trucks {0679, 0756, 7200, 7201, 7213}
High Pitch Noise from the Flushing Valve May Occur on Certain Skid Steer Loaders {4351, 5058} High Pitch Noise from the Flushing Valve May Occur on Certain Skid Steer Loaders {4351, 5058}
Installation Procedure of the Gusset Plate in the Frame Assembly on Certain HF201B Felling Heads {6319} Installation Procedure of the Gusset Plate in the Frame Assembly on Certain HF201B Felling Heads {6319}
New Gusset Plate in the Frame Assembly Is Now Used on Certain HF201B Felling Heads {6319} New Gusset Plate in the Frame Assembly Is Now Used on Certain HF201B Felling Heads {6319}