Exhaust System Contains Oil
- Extended idle times
- Failed turbocharger seals
- Worn valve guide seals or faulty valve guide seals
- Worn valve guides
- Worn piston rings
Complete the procedure in the order in which the steps are listed.
Show/hide table
| Troubleshooting Test Steps | Values | Results |
|---|---|---|
1. Extended Idle Times A. Extended idle times will allow oil to pass into the exhaust system. |
Idle times |
Result The idle times are extensive. Reduce the idle times. Proceed to Test Step 6. Result The idle times are not extensive. Proceed to Test Step 2. |
2. Failed Turbocharger Seals A. Check the inlet manifold and the exhaust manifold for oil. |
Turbo seals |
Result: Oil is present in the inlet or exhaust manifold. Repair: Replace the leaking turbocharger. Verify the repair. Proceed to Test Step 6. Result: Oil is not present in the inlet or exhaust manifold. Proceed to Test Step 3. |
3. Worn Valve Guide Seals or Faulty Valve Guide Seals A. Inspect the valve guide seals for wear and for damage. |
Valve guide seals |
Result: The valve guide seals are damaged. Repair: Replace the valve guide seals. Verify the repair. Proceed to Test Step 6. Result: The valve guide seals are not damaged. Proceed to Test Step 4. |
4. Worn Valve Guides A. Inspect the valve guides for wear. Refer to the Specification manual for the maximum permissible wear of the valve guides. |
Valve guides |
Result: The valve guides are worn. Repair: If necessary, recondition the cylinder head. Verify the repair. Proceed to Test Step 6. Result: The valve guides are not worn. Proceed to Test Step 5. |
5. Worn Piston Rings A. Remove the pistons. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Remove". B. Remove the piston rings from the pistons. Refer to Disassembly and Assembly, "Pistons and Connecting Rods - Disassemble" C. Inspect the pistons and piston rings for wear or damage. Refer to the "Specifications" manual for further information. |
Piston rings |
Result The piston rings are worn. Repair: Replace the piston rings. Verify the repair. Proceed to Test Step 6. Result The piston rings are not worn. Contact the Dealer Solutions Network (DSN). |
6. Check the Aftertreatment System for Oil A. Remove excess oil from piping with a clean cloth. B. Remove the Clean Emissions Module (CEM). Refer to Disassembly and Assembly, "Clean Emissions Module - Remove and Install". C. Support the CEM over a suitable container with the exhaust inlet downwards. Leave the CEM to drain for 8 hours. D. Check the quantity of drained oil in the container. |
CEM |
Result The volume of drained oil is greater than Repair: Install a replacement CEM. Refer to Disassembly and Assembly, "Clean Emissions Module - Remove and Install". Return the unit to service. Result The volume of drained oil is less than Proceed to Test Step 7. |
7. Recover the Aftertreatment System A. Clean any remaining oil from the piping and the CEM inlet with a clean cloth. B. Install the Clean Emissions Module (CEM). Refer to Disassembly and Assembly, "Clean Emissions Module - Remove and Install". C. Run the engine at high idle with no load for a minimum of 20 minutes. D. Use the electronic service tool to perform the "Aftertreatment Recovery Procedure". While the procedure is progressing, check for smoke from the exhaust. Some smoke will be evident during the procedure. The smoke must dissipate before the procedure is completed. |
CEM |
Result: The "Aftertreatment Recovery Procedure" completes with a soot load of less than 80% and no smoke from the exhaust. Return the unit to service. Result The "Aftertreatment Recovery Procedure" completes with a soot load of more than 80% or smoke from the exhaust. Contact the Dealer Solutions Network (DSN). |
Caterpillar Information System:
980L Tier 3 Wheel Loader Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
C7.1 Engines and Generator Sets Exhaust System Contains Fuel
C7.1 Engines and Generator Sets Exhaust System Contains Coolant
CB7, CB8 and CB10 Vibratory Asphalt Compactors Power Train Drum Mounting
980M Tier 4 and 982M Tier 4 Wheel Loader Engine Supplement Engine Oil Cooler - Remove and Install
994K Wheel Loader Machine Systems Seat - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Pilot Pressure - Test and Adjust
A New Support Assembly Is Now Used on Certain C9.3 Machine Engines {1405, 1802} A New Support Assembly Is Now Used on Certain C9.3 Machine Engines {1405, 1802}
Cab Heater Hoses May Rub Against the Cross Member on Certain PL61 Pipelayers {7304} Cab Heater Hoses May Rub Against the Cross Member on Certain PL61 Pipelayers {7304}
Index of Reuse and Salvage Guidelines for the CX38 Transmission {0374, 0599, 0700, 0722, 3030, 3065} Index of Reuse and Salvage Guidelines for the CX38 Transmission {0374, 0599, 0700, 0722, 3030, 3065}
2570D and 2670D Wheel Feller Buncher Engine Supplement Fan - Remove and Install
A New Ground Strap for Wiring Group is Now Used On Certain 794 AC Off-Highway Trucks {1408, 3260, 3282} A New Ground Strap for Wiring Group is Now Used On Certain 794 AC Off-Highway Trucks {1408, 3260, 3282}
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Remove and Install
Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380} Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380}
C7.1 Engines and Generator Sets Fuel Consumption Is Excessive
MH3037 Material Handler Machine Systems Main Control Valve - Remove and Install - Lower Valve
C7.1 Engines and Generator Sets Fuel Contains Water
2570D and 2670D Wheel Feller Buncher Engine Supplement Piston Motor (Fan) - Remove and Install
C7.1 Engines and Generator Sets Fuel Rail Pressure Problem
C7.1 Engines and Generator Sets Fuel Temperature Is High
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Disassemble
C7.1 Engines and Generator Sets Inlet Air Is Restricted
980L Tier 3 Wheel Loader Engine Supplement Expansion Tank - Remove and Install
C7.1 Engines and Generator Sets Intake Manifold Air Pressure Is High