Exhaust System Contains Coolant
Use the following procedure to troubleshoot a problem with coolant in the exhaust system.
- NOx Reduction System (NRS) cooler
- Cylinder head gasket
- Cylinder head
- Cylinder block
Note: The procedures have been listed in order of probability. Complete the procedures in order.
Show/hide table
Troubleshooting Test Steps | Values | Results |
---|---|---|
1. NRS cooler A. Check the NRS cooler for leaks for utilizing the "On Engine Test Procedure". Refer to Systems Operation, Testing, and Adjusting, "Exhaust Cooler (NRS) - Test". |
NRS cooler |
Result : The NRS cooler has a leak. Repair: Replace the NRS cooler. Refer to the Disassembly and Assembly manual for the correct procedure. Result : The NRS cooler does not have a leak. Proceed to Test Step 2. |
2. Cylinder head gasket leak A. Check the cylinder head gasket for leaks. |
Cylinder head gasket |
Result : The cylinder head gasket is leaking. Proceed to Test Step 3. Result : The cylinder head gasket is not leaking. Proceed to Test Step 3. |
3. Cylinder head A. Check for cracks in the cylinder head. Perform a leak test on the cylinder head. Refer to the Systems Operation, Testing, and Adjusting, "Cylinder Head - Inspect" for the correct procedure. |
Cylinder head |
Result : A crack is found in the cylinder head. Repair: Repair the cylinder head or replace the cylinder head. Refer to the Disassembly and Assembly manual. Proceed to Test Step 4. Result : The cylinder head is OK. Proceed to Test Step 4. |
4. Cylinder Block A. Check for cracks in top face of the cylinder block. Refer to the Systems Operation, Testing, and Adjusting, "Cylinder Block - Inspect" for the correct procedure. |
Cylinder head |
Result : A crack is found in the cylinder block. Repair: Repair the cylinder block or replace the cylinder block. Refer to the Disassembly and Assembly manual. Repair: Assemble the cylinder head with a new cylinder head gasket. Refer to the Disassembly and Assembly manual. Result : The cylinder block is OK. Repair: Assemble the cylinder head with a new cylinder head gasket. Refer to the Disassembly and Assembly manual. |
Caterpillar Information System:
CB7, CB8 and CB10 Vibratory Asphalt Compactors Power Train Drum Mounting
980M Tier 4 and 982M Tier 4 Wheel Loader Engine Supplement Engine Oil Cooler - Remove and Install
994K Wheel Loader Machine Systems Seat - Remove and Install
R1700 Load Haul Dump Power Train, Steering, Braking, Hydraulic, and Machine Systems Pilot Pressure - Test and Adjust
A New Support Assembly Is Now Used on Certain C9.3 Machine Engines {1405, 1802} A New Support Assembly Is Now Used on Certain C9.3 Machine Engines {1405, 1802}
Cab Heater Hoses May Rub Against the Cross Member on Certain PL61 Pipelayers {7304} Cab Heater Hoses May Rub Against the Cross Member on Certain PL61 Pipelayers {7304}
Index of Reuse and Salvage Guidelines for the CX38 Transmission {0374, 0599, 0700, 0722, 3030, 3065} Index of Reuse and Salvage Guidelines for the CX38 Transmission {0374, 0599, 0700, 0722, 3030, 3065}
2570D and 2670D Wheel Feller Buncher Engine Supplement Fan - Remove and Install
A New Ground Strap for Wiring Group is Now Used On Certain 794 AC Off-Highway Trucks {1408, 3260, 3282} A New Ground Strap for Wiring Group is Now Used On Certain 794 AC Off-Highway Trucks {1408, 3260, 3282}
Installation of the 519-9196 Lines Gp - Coupler on Certain Backhoe Loaders {5057, 5133, 6129} Installation of the 519-9196 Lines Gp - Coupler on Certain Backhoe Loaders {5057, 5133, 6129}
C175-16 and C175-20 Engines for Caterpillar Built Machines Engine Oil Filter Housing - Remove and Install
MH3037 Material Handler Machine Systems Piston Motor (Swing) - Assemble
C7.1 Engines and Generator Sets Exhaust System Contains Fuel
980L Tier 3 Wheel Loader Engine Supplement Engine Oil Filter and Oil Filter Base - Remove and Install
C7.1 Engines and Generator Sets Exhaust System Contains Oil
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Remove and Install
Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380} Improved Coolant Tube Flanges for the Brake Oil Bonnets are Now Used on Certain 793D Off-Highway Trucks {1380}
C7.1 Engines and Generator Sets Fuel Consumption Is Excessive
MH3037 Material Handler Machine Systems Main Control Valve - Remove and Install - Lower Valve
C7.1 Engines and Generator Sets Fuel Contains Water
2570D and 2670D Wheel Feller Buncher Engine Supplement Piston Motor (Fan) - Remove and Install
C7.1 Engines and Generator Sets Fuel Rail Pressure Problem
C7.1 Engines and Generator Sets Fuel Temperature Is High
980L Tier 3 Wheel Loader Machine System Piston Pump (Implement) - Disassemble