Boom Group
"Adjust（调整）"菜单允许用户调整各种 "Adjust Group（调整组）"屏幕上列出的传感器、控制和系统。 更改 "Boom Group（动臂组）"参数包括按特定系数改变主机程序。 要调整 "Boom Group（动臂组）"的设置，执行下述步骤。
- 按下菜单按钮 (1) 以启用 "Main（主）"菜单。
Show/hide table
 | |
| 图 1 | g01201729 |
- 从 "Main（主）"菜单，按下按钮 (F1) 以选择 "Adjust（调整）"菜单。
Show/hide table
 | |
| 图 2 | g03131817 |
典型 "Main（主）"菜单 | |
- 从调整菜单，使用按钮旋钮 (2) 滚动到 "Boom Group（动臂组）"
- 按下按钮旋钮 (2) ，以选择 "Boom Group（动臂组）"。
要调整 Boom Group（动臂组）的设置，执行下述步骤。
- 将会弹出一个 PIN 代码输入框。 默认 "Service（维修）"PIN 代码是 "1111"。 输入 PIN 代码。
Show/hide table
 | |
| 图 3 | g03348022 |
"Boom Group（动臂组）"菜单的典型 PIN 代码输入 | |
从 "Boom Group（动臂组）"菜单，使用按钮旋钮 (2) 滚动至需要更改的参数。
Show/hide table
 | |
| 图 4 | g03348023 |
典型 "Boom Group（动臂组）"菜单 | |
Show/hide table
 | |
| 图 5 | g03348041 |
"Boom Down（动臂降下）"屏幕 （典型 "Boom Group（动臂组）"菜单选择） | |
使用功能按钮突出显示动臂降下 (F4) 或动臂升起 (F5)，以选择要更改的设置。
选择最小 (A) 以设置最小 mA 控制电流值。
选择最大 (B) 以设置最大 mA 控制电流值。
选择启动 (C) 以设置启动电流延迟时间毫秒。
选择启动 (D) 以设置停止电流延迟时间毫秒。
旋转按钮旋钮 (2) 以更改数值。 按下按钮旋钮 (2) 的中间，以保存您的选择。
Caterpillar Information System:
MH3037, MH3049 and MH3059 Material Handlers IQAN Monitoring & Control System Auxiliary Group
MH3049 Material Handler Machine Systems Cab - Remove and Install
2014/04/15 An Improved Lip Type Seal and Wear Sleeve Seal Are Now Used in the Transfer Gear Group of Certain 777 Off-Highway Trucks {3159}
966M Tier 4, 966M Tier 4 Series XE, 972M Tier 4 and 972M Tier 4 Series XE Wheel Loaders Diesel Exhaust Fluid Module - Remove and Install
773F and 775F Off-Highway Truck Engine Components - Clean/Inspect, Rebuild/Install Reman, Install New
Product Link ™ PLE702, PLE601, PLE602, PLE602P, PL641, PL641V2, PL631, PL631V2, PL542, PL240, PL240B, PL241, PL131, PL141, PL161, and PL042 Systems System Overview
Product Link ™ PLE702, PLE601, PLE602, PLE602P, PL641, PL641V2, PL631, PL631V2, PL542, PL240, PL240B, PL241, PL131, PL141, PL161, and PL042 Systems General Hazard Information
Product Link ™ PLE702, PLE601, PLE602, PLE602P, PL641, PL641V2, PL631, PL631V2, PL542, PL240, PL240B, PL241, PL131, PL141, PL161, and PL042 Systems Safety Signs and Labels
C7.1 Engines for Caterpillar Built Machines Fuel Injection Timing - Check
AP1000F Asphalt Paver Operator Controls
C7.1 Engines for Caterpillar Built Machines Air in Fuel - Test
2384C, 2484C, 559C and 579C Knuckleboom Loaders Machine Systems Stick Cylinder - Remove and Install
MH3037, MH3049 and MH3059 Material Handlers IQAN Monitoring & Control System Function Group
R1600G Load Haul Dump Braking System Service and Parking Brake System
793F Tier IV Off-Highway Truck Field Assembly Mirror - Install - Rear View
R1600G Load Haul Dump Braking System Brake Release System
R1600H Load Haul Dump Machine Systems Control Valve (STIC Steering) - Disassemble
R1600G Load Haul Dump Machine Systems Control Valve (STIC Steering) - Assemble
793F Tier IV Off-Highway Truck Field Assembly Fender - Install - Mud Guards
R2900G Load Haul Dump Braking System Pressure Sensor (Service Brake Oil)
AD45B Underground Articulated Truck Braking System Pressure Sensor (Service Brake Oil)
MH3049 Material Handler Machine System Cab Riser Cylinder
2013/03/04 An Improved Platform Wiring Gp Is Introduced in 424B Backhoe Loaders {1408}
259D, 279D, 289D, 299D and 299D XHP Compact Track Loaders, 257D, 277D, 287D, 297D and 297D XHP Multi Terrain Loaders and 236D, 242D, 246D, 262D, 272D and 272D XHP Skid Steer Loaders Machine Systems Piston Pump - Remove and Install - Standard Flow